+
≠
+
≠
+
≠
+
≠
+
≠
+
≠
V
23.
iolet
12.
25. With a 2 speaker system, do not
connect anything to the speaker leads
that are not connected to speakers.
r
12. Rea speaker
16.
Right
Rear speaker
24. Violet/black
20. Gray/black
14. Front speaker
19. Gray
17. White
18. White/black
21. Green
22. Green/black
15.
Left
14. Front speaker
12. Rear speaker
12. Rear speaker
13.
8. System remote control
5. Connecting cords with RCA
pin plugs (sold separately)
7. Power amp
(sold separately)
6. Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal (max. 300 mA
12 V DC).
1. This Product
2. Rear output
3. Antenna jack
9. Yellow
To terminal always supplied with
power regardless of ignition
switch position.
10. Red
To electric terminal controlled by
ignition switch (12 V DC)
ON/OFF.
11. Black (ground)
To vehicle (metal) body.
Perform these connections when using
the optional amplifier.
4. Fuse (10 A)
Note:
•
This unit is for vehicles with a 12-volt battery
and negative grounding. Before installing it in a
recreational vehicle, truck, or bus, check the bat-
tery voltage.
•
To avoid shorts in the electrical system, be sure
to disconnect the
≠
battery cable before begin-
ning installation.
•
Refer to the owner’s manual for details on con-
necting the power amp and other units, then
make connections correctly.
•
Secure the wiring with cable clamps or adhesive
tape. To protect the wiring, wrap adhesive tape
around them where they lie against metal parts.
•
Route and secure all wiring so it cannot touch
any moving parts, such as the gear shift, hand-
brake and seat rails. Do not route wiring in
places that get hot, such as near the heater outlet.
If the insulation of the wiring melts or gets torn,
there is a danger of the wiring short-circuiting to
the vehicle body.
•
Don’t pass the yellow lead through a hole into
the engine compartment to connect to the battery.
This will damage the lead insulation and cause a
very dangerous short.
•
Do not shorten any leads. If you do, the protec-
tion circuit may fail to work when it should.
•
Never feed power to other equipment by cutting
the insulation of the power supply lead of the
unit and tapping into the lead. The current capac-
ity of the lead will be exceeded, causing over-
heating.
•
When replacing the fuse, be sure to only use a
fuse of the rating prescribed on this unit.
•
Since a unique BPTL circuit is employed, never
wire so the speaker leads are directly grounded or
the left and right
≠
speaker leads are common.
•
Speakers connected to this unit must be high-
power with minimum rating of 50 W and imped-
ance of 4 to 8 ohms. Connecting speakers with
output and/or impedance values other than those
noted here may result in the speakers catching
fire, emitting smoke, or becoming damaged.
•
When this product’s source is switched ON, a
control signal is output through the blue/white
lead. Connect to an external power amp’s system
remote control or the car’s Auto-antenna relay
control terminal (max. 300 mA 12 V DC). If the
car features a glass antenna, connect to the anten-
na booster power supply terminal.
•
When an external power amp is being used with
this system, be sure not to connect the blue/white
lead to the amp’s power terminal. Likewise, do
not connect the blue/white lead to the power ter-
minal of the auto-antenna. Such connection could
cause excessive current drain and malfunction.
•
To avoid a short-circuit, cover the disconnected
lead with insulating tape. Insulate the unused
speaker leads without fail. There is a possibility
of a short-circuit if the leads are not insulated.
•
If this unit is installed in a vehicle that does not
have an ACC (accessory) position on the ignition
switch, the red lead of the unit should be con-
nected to a terminal coupled with ignition switch
ON/OFF operations. If this is not done, the vehi-
cle battery may be drained when you are away
from the vehicle for several hours.
•
The black lead is ground. Please ground this lead
separately from the ground of high-current prod-
ucts such as power amps.
If you ground the products together and the
ground becomes detached, there is a risk of dam-
age to the products or fire.
•
Cords for this product and those for other prod-
ucts may be different colors even if they have
the same function. When connecting this prod-
uct to another product, refer to the supplied
manuals of both products and connect cords that
have the same function.
Connecting the Units
ACC position
ACC
ON
S
T
A
R
T
O
FF
ON
S
T
A
R
T
O
FF
No ACC position
<ENGLISH>
Connection Diagram (Fig. 8)
1. This Product
2. Rear output
3. Antenna jack
4. Fuse (10 A)
5. Connecting cords with RCA pin plugs (sold sep-
arately)
6. Blue/white
To system control terminal of the power amp or
Auto-antenna relay control terminal
(max. 300 mA 12 V DC).
7. Power amp (sold separately)
8. System remote control
9. Yellow
To terminal always supplied with power regard-
less of ignition switch position.
10. Red
To electric terminal controlled by ignition switch
(12 V DC) ON/OFF.
11. Black (ground)
To vehicle (metal) body.
12. Rear speaker
13. Perform these connections when using the
optional amplifier.
14. Front speaker
15. Left
16. Right
17. White
18. White/black
19. Gray
20. Gray/black
21. Green
22. Green/black
23. Violet
24. Violet/black
25. With a 2 speaker system, do not connect anything
to the speaker leads that are not connected to
speakers.
Fig. 8
∏ qJA«
