DVD-V8000
95
5
6
7
8
5
6
7
8
C
D
F
A
B
E
FL
Description of
Error
Causes if with a DVD
Causes if with a CD
Operation of the Unit
74
Subcode check
failure during startup
Subcode could not be read within 1
second after the tracking on.
Open (Subcode readout
failure)
A1
Communication
timeout of DSP
command
A command could not be issued to DSP because
Command Busy (XCBUSY) was in force
(XCBUSY = L) for a specified time (about 200
µ
S).
Open
A2
Communication
timeout for reading
DSP coefficient
Command Busy (XCBUSY) was in force for a
specified time (about 200
µ
S) before and after a
coefficient read command was issued to DSP, or
the address echo-back after command issuance
did not match the setup address.
Open
A4
Communication
timeout for
continuously writing
DSP coefficient
Command Busy (XCBUSY) was in force for 200
µ
S during continuous coefficient writing, or before
and after a continuous write command was
issued to DSP.
Open
B1
Timeout error for
backup
In the backup sequence, codes could not be read for fixed time.
Stop
B2
Retry error for
backup
Cannot close tracking even if performs backup fixed number of times.
Stop
B3 Retry error for trace
During tracing, do not restore after the runaway detection backup was performed
several times.
Stop
C3
Detection of tracking
overcurrent
During playback, the overcurrent detection port was at L for 300 ms or more
continuously.
Stop (the mechanical
controller operates
independently).
(C5)
Short-circuit test
corresponding error
After the overcurrent detection (C3 error), furthermore the overcurrent detection port
was at L for 300 mS or more continuously.
Turns off the power
instantly (No indication on
the LCD display and no
writing to flash memory)
F5 Tray being pushed
The tray switch that had been Open mode was forcibly changed to a mode other
than Open by an external force.
Close
F6 Code reading NG
(PRD) In the CD starting, when a
subcode of TOC part was not
readable, but the subcode of the
program area was readable.
Search, scan and special
playback prohibition,
Playback as playback CD-
R (PRD mode) as it is.
F8 Loading timeout
Loading or unloading could not be completed
within a specified time (about 10 seconds).
Though a portable cover is opening, when a
close command was issued from the system
controller.
Reverses the loading
direction. It timeout is
repeated upon retry, the
unit stops.
FC Focus
• Focus ON sequence could not be completed more than two seconds.
• Auto sequence command was finished, actually focus ON was not completed.
• Focus did not enter even if retried it eight times.
Stops wherever possible
then opens (stops in the
case of side B).
LCD
Description of Error
Causes if with a DVD
Causes if with a CD
Operation of the Unit
No operation or it becomes debugging
indication if the power is able to ON.
bit3=1 08 etc.
AV1 access error
(read, write NG)
bit2=1 04 etc.
EBY-CHIP access error
bit0=1 01 etc.
SRAM access error
Error codes that are displayed on the LCD display by using the remote control unit (Device error)
To display: ESC + D DISPLAY; Location of the display: At the two digits of left of the LCD display
Содержание CB-A802
