Pioneer CB-A802 Скачать руководство пользователя страница 102

Страница: 102 / 168

DVD-V8000

102

Tray open?

Is the

Power-on-Start

setting made?

Is an error

detected?

Is it

a start time programmed

by the timer?

Yes

Is a disc

installed?

Yes

Tray close

Stop

The unit will be stopped, and an error
indication will be displayed on the LCD.

Timer start?

Power on start?

Is there a

First Play PGC?

Yes

The target that has been programmed is
searched for and playback will start.

Yes

Playback starts according to the navigation.

Yes

Set the address

of the target.

Yes

Set the address

of the target.

Disc judgment

: If there is a problem in closing of the tray,
an error indication is displayed on the LCD.

Stop

Содержание CB-A802









































































































































































Результаты поиска

Содержание CB-A802

Отзывы:

Похожие инструкции для CB-A802

Бренды по названию

Популярные бренды

Pioneer CB-A802, Руководство по обслуживанию

Результаты поиска

Содержание CB-A802

Отзывы:

Похожие инструкции для CB-A802

Бренды по названию

Популярные бренды