background image

4

Safety Precautions

Anyone operating the machine should read the 

following carefully and be informed of potentially 

dangerous operating conditions. Operators should 

be familiar with the location and use of all safety 

devices on the machine. DO NOT use the machine 

if it is not in proper operating condition, and report 

any damage or operation faults immediately.

DANGER!

  

Failure to read the Owner’s Manual prior to operating or 

attempting any service or maintenance procedure to your machine 

could result in injury to you or to other personnel; damage to the 

machine or to other property could occur as well. You must have 

training in the operation of this machine before using it. If you or 

your operator(s) cannot read English, have this manual explained 

fully before attempting to operate this machine.

DANGER!

  

To reduce the risk of fire, use only commercially 

available floor cleaners, strippers, and waxes intended for machine 

application.

DANGER!

  

Risk of explosion. Floor sanding can result in an 

explosive mixture of fine dust and air. To reduce risk of explosion, 

use floor sanding machine only in well ventilated area.

DANGER!

  

Operating a machine that is not completely or fully 

assembled could result in injury or property damage. DO NOT 

operate this machine until it is completely assembled. Inspect the 

machine carefully before operation.

DANGER!

  

Electrocution could occur if maintenance and repairs are 

performed on a unit that is not disconnected from the power source. 

Disconnect the power supply before attempting any maintenance or 

service. Always remove the electrical plug from the electrical outlet 

before changing the brush, pad or other attachment and before 

leaving the machine.

DANGER!

  

Using a machine with a damaged power cord could result 

in an electrocution. DO NOT use the machine if the power cord is 

damaged. DO NOT use the electrical cord to move the machine.

WARNING! 

 Water solutions used with this type of machine can 

leave wet areas on the floor surface. These areas can cause a 

dangerous condition for the operator or other persons. Always put 

“CAUTION” signs near the area being cleaned.

WARNING!  

Modifications or alterations to this machine can lead 

to personal injury or damage to the machine. DO NOT make 

unauthorized modifications or alterations to this machine. Amano 

Pioneer Eclipse assumes no liabilities for injury or damage resulting 

from an unauthorized modification or alteration to the machine.  Any 

unauthorized modification or alteration to this machine voids all 

warranties.

WARNING!

  

Electrical components of this machine can “short-out” if 

exposed to water or moisture. Keep the electrical components of the 

machine dry. Wipe the machine down after each use. For storage, 

keep the machine in a dry building.

WARNING!

  

Always use a three-wire electrical system connected to 

the electrical ground. For maximum protection against electric shock, 

use a circuit that is protected by a ground fault interrupter. Consult 

your electrical contractor.

WARNING!

  

To prevent damage to the power cord, DO NOT let the 

brush, pad, pad driver or wheels touch the power cord when the 

machine is running. Always lift the cord over the machine. DO NOT 

pull the power cord to move the machine.

WARNING!

  

Operating a machine without observing all labels and 

instructional information could result in injury or damage. Read all 

machine labels before attempting to operate. Make sure all of the 

labels and instructional information are attached or fastened to the 

machine. Get replacement labels and decals from your authorized 

distributor.

WARNING!  

Sanding wood or varnish produces dust that could self 

ignite and could cause injury or damage. Dispose accordingly.

WARNING!  

Use of this machine as a step or furniture could result in 

injury or damage. DO NOT use this machine as a step or furniture. 

DO NOT ride on this machine.

WARNING!

  

To avoid injury keep hands, feet and loose clothing away from all 

moving parts of this machine.

WARNING!

 

Injury to operator or bystanders could occur if an abrupt 

change in floor surface texture is encountered when using this 

machine. Abrupt change in floor surface texture can cause a sudden 

pulling motion by this machine. This sudden pulling motion can result 

in loss of control of the machine which could injure the operator or 

bystanders. Avoid motions that could cause machine to cross from 

a smooth floor surface to a carpeted or rough texture floor surface 

Avoid motions that could allow the machine to come in contact with 

low obstacles, such as floor electrical outlets, door stops or entry 

molding, etc.

WARNING!

 

Any alterations or modifications of this machine could 

result in damage to the machine or injury to the operator or other 

bystanders. Alterations or modifications not authorized by the 

manufacturer voids any and all warranties and liabilities.

CAUTION!

 

The machine is heavy. Get assistance before attempting 

to transport or move it.

CAUTION!

 

When draining liquids from the machine, follow all local 

and federal waste disposal standards.

 

Содержание PE225FP





























Отзывы: