Pinnacle GBU070 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 29

background image

TURNING OFF THE UNIT

Turn the power switch to draft fan. Fuel will stop feeding but the draft fan will remain
running. Let run until fire burns out completely. Set power switch to off.

NOTE: Approximately 10 – 12 minutes should be enough time for fire to burn out. Time will
vary depending on fuel type.

MAINTENANCE

1. Check the ash pan regularly and empty as necessary. Dispose of the ashes in a metal

container, and when cooled, bury them to prevent any spontaneous fires.

2. Check the fire pot regularly for any residue build-up. Clean and dispose of them when

completely cooled.

3. Remove the two heat exchanger access panels twice per burning season and check the

heat exchanger for ash. Vacuum if necessary. Replace gasket material if any tearing or

deterioration occurs.

4. Annually check the blowers for lint deposits from carpeting, dryer lint, furniture

coverings, pet hair, etc.

5. Inspect the flue pipe or vent assembly and chimney each time the heat exchanger is

serviced (minimum twice per heating season). Clean these passages as needed. Higher
usage of the unit could require more frequent cleanings.

6.

Your unit is equipped with an aluminium air filter, wash and clean it regularly. At least
once a month

.

11

«
...
10
11
12
13
14
...
»

Содержание GBU070






























Отзывы:

Нет отзывов

Похожие инструкции для GBU070

Бренд: HAAS + SOHN Страницы: 23

Бренд: VARDE OVNE Страницы: 2

Бренд: Piazzetta Страницы: 70

Бренд: KASTOR Страницы: 54

Бренд: ECG Страницы: 60

Бренд: AGA Страницы: 34

Бренд: Comfort Glow Страницы: 13

Stove with 3,6 kW PnP

Бренд: Karibu Страницы: 68

Бренд: NESTOR MARTIN Страницы: 88

Advantage II-T C FS

Бренд: Whitfield Страницы: 48

Бренд: Whitfield Страницы: 48

Advantage Optima 2 FS

Бренд: Whitfield Страницы: 54

Бренд: Valor Fires Страницы: 8

Q-Tee II INSERT USA Series

Бренд: RAIS Страницы: 62

Winchester WINACP

Бренд: Magnum Страницы: 51

Бренд: Olsberg Страницы: 36

Turia Lina Compact Series

Бренд: Olsberg Страницы: 44

Бренд: GDC Group Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды