Propane Supply (Continued)
-
Do not use a flame to check for leaks!
Use a 50/50
solution of dish soap and water to check for leaks.
Repair any leaks before attempt-ing to re-light the
heater.
- Check the “O” ring on the heater inlet fuel connector for
damage before each use. Replace if damaged or worn.
- Always store the LP cylinder outdoors, but not in an
enclosed area. Never store the LP cylinder near high
heat, direct sunlight or open flames. Never store the LP
cylinder indoors.
- The amount of LP gas used by this heater varies. The
two factors that will determine this are as follows:
1
.The amount of gas in the cylinder.
2
.The temperature of the cylinder and surrounding area.
Ventilation
For this heater, provide a minimum of 48 square inches of
space by opening a window or door to provide fresh, out-
side air. For additional heaters, provide more ventilation.
Provide at least 3 square feet of opening for ventilation per
100,000 Btu of rated operation.
Assembly
-
Tools required:
Medium phillips screwdriver
Model PT-30-TT
1. Place Tank Collar Bracket on top of Center Plate. Be
sure Mounting Bolt Knob is on bottom as shown in
Figure 2.
2. Insert Machine Screw into top hole using Phillips
screwdriver.
4. Insert 2nd Machine screw into bottom hole. This will
secure the Tank Collar Bracket to the Center Plate.
Model PT-30-TT-P
1. Place Piezo Bracket in front of Center Plate and line up
holes with pins on Center Plate.Be sure Piezo Ignitor is
on top as shown in Figure 2.
2. Place Tank Collar Bracket on top of Piezo Bracket. Be
sure Mounting Bolt Knob is on bottom as shown in
Figure 2.
3. Insert Machine Screw into top hole using Phillips
screwdriver.
4. Insert 2nd Machine screw into bottom hole. This will
secure the Piezo Bracket and Tank Collar Bracket to the
Center Plate.
Connecting Heater to LP Cylinder
Be sure to read and understand all of the Safety
Information in this manual before connecting the
heater to the LP cylinder.
Single Burner Models Only
1. Be sure that the control knob on the regulator is in the
“OFF” position.
2. Line up the threads on the Fuel Connector Nut with the
threads on the LP cylinder valve. Turn Fuel Connector
Nut counterclockwise to tighten. Use a wrench to fully
tighten the nut, being careful not to overtighten.
3. Slowly open the LP cylinder valve.
4. Check all connections for leaks using a 50/50 mixture of
dishsoap and water. Any bubbles appearing show a
leak. Remove and reconnect the Connector Nut to the
valve.
Double Burner Models Only
1. Be sure that the control knob on the regulator is in the
“OFF” position.
2. Line up the slots in the tank collar bracket with the tank
collar ring and slide into place. Be sure the mounting
knob is to the outside, and tighten.
3. Line up the threads on the Fuel Connector Nut with the
threads on the LP cylinder valve. Turn Fuel Connector
Nut counterclockwise to tighten. Use a wrench to fully
tighten the nut, being careful not to overtighten.
4. Slowly open the LP cylinder valve.
5. Check all connections for leaks using a 50/50 mixture of
dishsoap and water. Any bubbles appearing show a
leak. Remove and reconnect the Connector Nut to the
valve.
Page 4
Pinnacle Products International, Inc. Tank Top User’s Manual
Extremely hot during operation. Do
not touch any metal components
while in operation. Keep gasoline and any other flam-
mable liquids away from heater. Not for use in resi-
dential living areas or in non-adequately ventilated
enclosed spaces.
DANGER
NEVER LEAVE HEATER
UNATTENDED WHILE BURN-
ING OR WHILE CONNECTED
TO A FUEL SOURCE
Propane
Tank Top Heaters
Spark Plug
Cable (Left)
Manifold
Center Plate
Piezo Igniter
Piezo Bracket
Tank Collar Bracket
Mounting Bolt Knob
Machine Screws
Fuel Connector
Nut
Regulator
Knob
Spark Plug
Cable (Right)
Figure 2.
Perspective view of heater
