manualshive.com logo in svg

Pilz 772 160, Руководство по эксплуатации

Поделиться
Скачать
Pilz 772 160 Скачать руководство пользователя страница 21

Function Description

Operating Manual PNOZ m EF 4AI
1004650-EN-02

| 21

Hysteresis:

2 threshold values are configured per switching threshold. One threshold value (switch-on
threshold) defines when the affected output is switched on. The second threshold value
(switch-off threshold) defines when the output will be switched off again.

Monitoring to "greater than"

mA

t

0

1

Switch-off threshold

Hysteresis

Switch-on threshold

Output

Monitoring to "less than"

mA

t

0

1

Switch-on threshold

Hysteresis

Switch-off threshold

Output

4.3.7

Range monitoring

In contrast to the threshold value monitoring, an upper and a lower switching threshold are
defined in the range monitoring.
This is to monitor both exceeding or dropping below a limit value.

Hysteresis:

2 threshold values are configured per switching threshold. One threshold value (switch-on
threshold) defines when the affected output is switched on. The second threshold value
(switch-off threshold) defines when the output will be switched off again.

Содержание 772 160








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды