Picor PI2003-EVAL1 Скачать руководство пользователя страница 2

The 

Cool-ORing

PI2003 with an external industry standard

100V N-channel MOSFET provides a complete Active ORing
solution designed for use in -48 Vbus redundant power
system architectures. The PI2003 controller with an N-channel
MOSFET enables extremely low power loss with fast dynamic
response to fault conditions, critical for high availability
systems. 

The PI2003 controller with a low Rds(on) N-channel MOSFET
provides very high efficiency and low power loss during
steady state operation.  The PI2003 controller provides an
active low fault flag output to the system during excessive
forward current, light load, or reverse current.

Figure 1 shows a photo of the PI2003-EVAL1 evaluation
board, with two PI2003 controllers and two N-channel
MOSFET used to form the two Active ORing channels. The
board is built with two identical Active ORing circuits with
options and features that enable the user to fully explore the
capabilities of the PI2003 universal Active ORing controller. 

Figure 1 

– PI2003 -EVAL1 Evaluation Board (1.8" x 1.8")

Terminals Rating

Vin1+ to Vin1-, 

60 V / 8 A

Vin2+ to Vin2-

60 V / 8 A

VC1, VC2

-0.3 V to 17.3 V / 40 mA

FT1, FT2

-0.3 V to 17.3 V / 10 mA

Terminal

Description

Vin1+ and Vin1-

Power Source Input #1: 

or bus input designed to accommodate up to 60 V and 6 A continuous current.

Vin1+ and Vin1-

Power Source Input #2: 

or bus input designed to accommodate up to 60 V and 6 A continuous current.

VC1 

Optional Auxiliary Input Voltage #1: 

to supply PI2003 VC power. VC1 should be 10 V or higher to fully enhance the MOSFET.

VC2 

Optional Auxiliary Input Voltage #1: 

to supply PI2003 VC power. VC1 should be 10.V or higher to fully enhance the MOSFET. 

FT1 

PI2003 (U1) Fault Pin: 

Monitors U1 fault conditions 

FT2 

PI2003 (U2) Fault Pin: 

Monitors U2 fault conditions

Vout + 

connected to input return

Vout-

Output -:

connected to MOSFETs sources

Table 1 

– PI2003-EVAL1 Evaluation Board terminals description  

Cool-ORing

TM

PI2003 Product Description

Picor Corporation • www.picorpower.com

PI2003-EVAL1 User Guide  Rev 1.0  

Page 2 of 8

Содержание PI2003-EVAL1










Отзывы: