PicoBox EMS-LTE Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 39

PicoBox EMS-LTE Скачать руководство пользователя страница 13

EMS-LTE User Manual

1234), click the "OK" to connect and start to program

Details, please check the picture as below:

Tips:

If not connect successfully, will not enter into next step. Pls check if USB connect well, or COM port and

password correct or not.

Setting Self-Checking

Phenomenon

Possible Reason

Can't enter software

1.

USB Driver installation failure;

2.

COM Port not correct or USB driver installation failure;

3.

Device not enter into setting mode:

1)

Only power light on, that means the Upgrade Firmware Switch at Load

side, not at Work side. Solution: Switch the power switch to OFF--->

Upgrade switch to Work side --- > Power switch to ON.
2)

Signal light flicks, that means device in working mode. Maybe had

not rebooted the device after switch mode switch to Set.

(In setting mode, Power light normal ON, Run light flicks, other lights Off.)

After switching panel on,

only Power light on,

panel can't work

1.

The Upgrade Firmware Switch at Load side, not at Work side.

Solution: Switch the power switch to OFF---->Upgrade switch to Work side ---- >

Power switch to ON;

2.

SD card fallout from the slot. Solution: Shake panel to listen if there is voice

or not;
3.

In upgrade mode, use upgrade tool erased the firmware.

Can't enter into working

mode

1.

The Upgrade Firmware Switch at Load side, not at Work side.

Solution: Switch the power switch to OFF---->Upgrade switch to Work side ---- >
Power switch to ON;
2.

Device in setting mode. Solution: Switch device OFF ---->Mode switch to

"Run" --- >Switch the device on.

Can't find COM Port

1.

Have not installed driver;

2.

PC system problem cause driver installation failure, can't support Apple

OS system.
3.Check USB line, and try other common driver software such as "Drive TheLife".

«
...
11
12
13
14
15
...
»

Содержание EMS-LTE








































Отзывы:

Нет отзывов