pico Technology TA133 Скачать руководство пользователя страница 9

Страница: 9 / 17

DO189-1

TA133-User’s Guide

Specifications

Electrical Characteristics

Input Resistance (System)

10 MΩ

± 1 %

Input Capacitance (System)

9.5 pF

(typical)

Compensation Range

10 pF - 25 pF

(typical)

Input Coupling of the Measuring Instrument

1 MΩ AC / DC

Input Impedance

Note that the input impedance of

the probe decreases as the frequency

of the applied signal increases.

Mechanical Characteristics

Weight (probe only)

48 g

Cable Length

1.2 m

Probe Tip Diameter

2.5 mm

Environmental specifications

Altitude

operating

up to 2000 m

non-operating

up to 15000 m

Temperature Range

operating

0° C to +50° C

non-operating

-40° C to +71° C

Maximum Relative Humidity

operating

80 % relative humidity for temperatures up to +31° C,

decreasing linearly to 40 % at +50° C

Typical Input Impedance PML711

100

10k

100k

10M

100M

100

10k

100k

10M 100M 1G

Frequency [Hz]

| [

]

Typical TA133 Input Impedance

Содержание TA133


















Результаты поиска

Содержание TA133

Отзывы:

pico Technology TA133, Руководство пользователя, Страница: 9 / 17

Результаты поиска

Содержание TA133

Отзывы: