pico Technology TA133 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 17

pico Technology TA133 Скачать руководство пользователя страница 10

10

© Copyright 2011 Pico Technology Ltd. All rights reserved

DO189-1

TA133-User’s Guide

Adjustment Procedures

The probe can be adjusted for low frequency (LF) compensation and for high frequency (HF) compensation.

LF Compensation

LF needs to be adjusted when the probe is connected to the oscilloscope input the first time. LF

compensation matches the probes cable capacitance to the oscilloscope input capacitance. This matching
assures good amplitude accuracy from DC to upper bandwidth limit frequencies. A poorly compensated probe

clearly influences the overall system performance (probe + scope) and introduces measurement errors

resulting in inaccurate readings and distorted waveforms.

LF compensation is performed by connecting the probe to the CAL – output on the oscilloscope front panel
and adjusting the LF compensation trimmer to optimum square wave response. For clarification see below

figures.

undercompensated

optimum

overcompensated

LF Compensation

«
...
8
9
10
11
12
...
»

Содержание TA133


















Отзывы:

Нет отзывов