PIAGGIO MP3 500 ie SPORT Business LT 2011 Скачать руководство пользователя

Страница: 271 / 375

PIN RELATIONSHIP

PIN

Component

Reference value

Lambda sensor

~ 0V with throttle valve closed; ~ 1V with

throttle valve fully opened

The Lambda sensor or oxygen sensor is a sensor which provides indications concerning the oxygen

content in the exhaust gas. The signal generated is not of the proportional type but of the ON/OFF type,

i.e. there is oxygen or there is not. The sensor is positioned on the exhaust manifold before the catalytic

converter in an area where the gas temperature is always high. The temperature at which the sensor

works is at least 350°C at 600°C and it has a reaction time of just 50 milliseconds. The signal generated

passes from a high value to a low value with a mixture with lambda =1.

Specific tooling

020481Y

Control unit interface wiring

020331Y

Digital multimeter

Install the electronic control unit interface wiring.

Start the engine and warm up until the electric fan

switches on.

Use an analogue multimeter with a direct voltage

scale measuring down to 2 V.

Place the tips of the multimeter between pins 4 (-)

and 11 (+)

With the engine running at idle speed, check that

the voltage oscillates between 0V and 1V

With the throttle valve completely open, the volt-

age is approx. 1V.

During the closing phase, the voltage is approx.

0V.

If the voltage remains constant, the sensor may be

damaged. Remove the sensor and check that

there are no oil or carbon deposits inside it..

MP3 500 ie SPORT Business LT (2011)

Injection

INJEC - 271

Содержание MP3 500 ie SPORT Business LT 2011
























































































































































































































































































































































































Результаты поиска

Содержание MP3 500 ie SPORT Business LT 2011

Отзывы:

Похожие инструкции для MP3 500 ie SPORT Business LT 2011

Бренды по названию

Популярные бренды

PIAGGIO MP3 500 ie SPORT Business LT 2011, Руководство пользователя

Результаты поиска

Содержание MP3 500 ie SPORT Business LT 2011

Отзывы:

Похожие инструкции для MP3 500 ie SPORT Business LT 2011

Бренды по названию

Популярные бренды