background image

-5-

PKI-0031

OFF

ON1

ON2

The numbers shown in the figure below indicate the sequence the parts should be installed.

Remove the (-) terminal 
from the battery.

Connect the lamp ground (-)  wire to chassy 
ground. This connection should be metal to 
metal. Scrape all rust, paint, dirt and under-
coating from the connection location.

Connect the lamp harness to 
the connector.

First ground the terminal then 

take the (-) cord (black) and 

connect it to the (-) terminal. 

Take the (+) terminal 
cord (white) and attach 
it to the (+) terminal and
connect to the battery

Attach the (-) terminal to 
the battery

【2】Relay Harness Installation Sequence

Secure relay bolt 
so that connector 
is facing downward.

Facing 
down

Connect the switch power (+) wire to a 
positive (+) lead for the reverse lights. 
To do so use the supplied connector or 

any connector that is suitable for this 

application. 

After all wires are connected test the system 
for operation.

Cord

One-touch connector

Run the PIAA harness from the engine compartment next 
to the battery back to the PIAA back-up lamp.Run the 
switch into the drivers compartment and mount it in a 
location that is easy for the driver to control and so that it 
is out of the way of other automotive functions.

After lamp has been installed, verify 
the relay harness does not make 
contact with the engineʼ s moving 
parts or sections that emit extreme 
heat. Use the wire tie included (Item 6) 
and secure to harnesses inside engine 
compartment.

Harness

Wire tie

If the switch is in position ON1 the PIAA back-up lamp will be on.
If the switch is in position ON2 the PIAA back-up lamp will only come on when the vehicle is in reverse and the 
vehicles factory reverse lights are on.
If the switch in the OFF position the PIAA back-up lamp system will be off.

Wires from fuse box
and relay must be 
pointing down

Battery

Black

Black

Black

Ground (-)

Ground (-)

White with 

Red Dots

White With 

Red Dots

Main 

Power (+)

(+) Switch 
Power

White With Red Dots

White With Red Dots

White With 

Red Dots

Remove the (+) terminal 
from the battery.

Содержание 2000 Back-Up












Отзывы: