background image

16

15

MAGNA

Liquid Crystal

MAGNA

Liquid Crystal

Cancelling Prints

Select ‘Cancel’ from the GUI.

Confirm your choice by selecting the green tick.

- Once the current layer is complete, the print will 

stop, and the print arm will return to its homing 

location. Wait for all movement to cease before 

opening the door of the printer. 

10. Leaving a finished print inside the printer for a 

time will allow excess resin to drip back into the vat.

11. When you are ready to clean the print, open 

the door. Refer to Section 7 for further guidance on 

cleaning prints. 

9. Liquid Crystal Magna does not need monitoring or 

supervision during the printing process, you do not 

need to be present when the print is due to finish.

To remove residual resin from printed parts and 

platforms, they will need to be cleaned. Photocentric 

recommends using the Photocentric Air Wash L.

The cleaning process is imperative for the quality of 

surface  finish  and  texture  after  post  exposure.  For 

further information on safe disposal of saturated 

resin cleaner and guidance on cleaning the wash 

unit, please refer to the Air Wash L User Manual.

Photocentric Resin Cleaners and Airwash L can be 

purchased 

here

The Airwash L User Manual can be downloaded from 

the support page 

here.

Here you can find guidance on installation, cleaning 

and emptying resin, and overall usage. 

1. Free the platform by turning the knob in an anti-

clockwise direction.

2. Grip the handles of the print platform securely and 

gently pull towards you to remove it.

3. Place the platform into the Air Wash L using 

the specifically designed attachment.

4. Please refer to Photocentric Resin/

Resin Cleaner TDS for guidelines on 

wash cycle time recommendations.

- Photocentric Resin Cleaner 30 TDS

5. Parts can be cleaned in 10 minutes using 

Photocentric Resin Cleaner 30. Refer to Resin 

TDS for recommended cleaning cycles.

7. Photocentric highly recommends using 

compressed air to dry parts thoroughly. 

Alternatively, leave rinsed parts aside to dry.

6. Once the print has been washed, rinse 

using water to remove excess resin and 

solvent. For Photocentric Resin Cleaner, 

rinse using hot water. For Photocentric Resin 

Cleaner 30, rinse using warm water.

7. CLEANING PRINTS

Air Wash L 

External dimensions are:

 620 (L) x 400 (W) x 990.5 (D) mm.
Capacity 90l (20 gallons)
Photocentric Air Wash L can be purchased from 

this 

webpage

.

The user manual for Air Wash L can be 

downloaded from this 

webpage

Here

  you  can  find  guidance  on  installation, 

cleaning and emptying saturated resin cleaner, 

and overall operation. 

NOTE: 

Handle printed parts with care as they are 

more fragile before post-exposure and avoid 

unnecessary exposure to light. 

NOTE: 

Please refer to Section 8 for guidance on curing 

printed parts.

NOTE: 

After removing the print platform from the printer, 

it can be helpful to tilt it and hold it over the 

vat to drain the excess resin. When carrying a 

finished print to your cleaning station, use paper 

towel or a suitable tray to catch any drips.

WARNING:

Do not t

ake printed parts off from the platform 

prior to the cleaning and post-curing steps. If 

removed, it may affect the dimensional accuracy 

of parts.

WARNING:

Wear gloves and safety glasses when working 

with Photocentric Resin Cleaners. 

Содержание LC MAGNA














Отзывы: