background image

3. Using a modeling knife, carefully cut out two line 

from the margin of the hole onto the wheel  pant.

    Just cut only one side of the wheel pant, where 

the main gear will install. Be sure to make a left 
and right wheel pant.

4.  Slide a 4.5mm nut/ two 16mm flat washers / 

4.5mm nut / collar / wheel / collar onto the axle.

5.   Slide the axle assembly into the wheel pant.

     

There are just one nut and two flat washers 

outside of the wheel pant.

6. Remove one nut, one flat washer. Attach the 

main landing gear to the axle.

7.  Center both collars and wheel in the middle of 

the wheel pant, lock both collars in place using 
a hexagon 2mm screw.

8.  With the landing gear in place, tighten two nuts.

28

6mm flat washer

!

    After installing the wheel pant, apply a small 

drop of thin C/A to the bottom nut.

9.  Repeat step # 1-8 to install the second wheel 

pant assembly.

MAIN GEAR INSTALLATION
INSTALLING THE MAIN LANDING GEAR

1. Four nuts have been installed at the factory.

2. Install main landing gear into the fuselage using  

(4) 4mm x 20mm machine screws and 16mm 
flat washers provided in the kit.

7

Screws

Glue with epoxy

26

Glue with epoxy

25

TAIL WHEEL INSTALLATION

1. Set the tail wheel assembly in place on the 

plywood plate.

2. Drill 2,6mm pilot holes through the plywood plate.

3.  Secure the tail wheel bracket in place using two 

3mm x 12mm screw.

4. Align the tail wheel wire so that the wire is 

parallel with the bottom of the rudder. The 
control clasp has a pre-drilled hole through the 
top of it. Slide this hole on to the tail wheel wire 
while sliding the clasp over the bottom of the 
rudder.

!

Drill

Cut

27

INSTALLING THE WHEEL PANTS

1.  Locate the wheel pants from the hardware bag. 

Mark the locations of the mounting axles onto 
the wheel pants. The locations of the two 
mounting holes are the middle of the wheel 
opening, on right side, left side and 10mm from 
the bottom of the wheel pant.

2. Using a 5mm drill bit, carefully drill two pilot 

holes through the wheel pant at the TWO 
marks you made.

Содержание decathlon - EP
















Отзывы: