background image

www.phoenixgold.com  

Amplifier Owner’s Manual

RMS Power Output 

150w x 4 @ 4 ohms Stereo

 

250w x 4 @ 2 ohms Stereo

 

500w x 2 @ 4 ohms Bridged

Power/Ground Wire Size: 

4 Gauge

Recommend Power Wire Fuse:  

       80a

Dimensions: 

       11.7” L x 7.1” W x 2.0” H

 

        296mm L x 180mm W x 52mm H

RMS Power Output 

        500w x 1 @ 4 ohms 

 

        800w x 1 @ 2 ohms

Recommend Power Wire Fuse:  

100a 

Power/Ground Wire Size: 

4 Gauge

Dimensions: 

       14.4” L x 7.1” W x 2.0” H

 

        366mm L x 180mm W x 52mm H

RMS Power Output 

125w x 4 @ 4 ohms Stereo

 

200w x 4 @ 2 ohms Stereo

 

400w x 2 @ 4 ohms Bridged

 

Key Features

ADAPT POWER MANAGEMENT SYSTEM
Full power output from 11 to 15 volts:

 

ADAPT delivers the same output 

power regardless of the vehicle’s electrical system voltage. Instantaneous or 

long term voltage drops have no effect on the amplifier’s power output. This 

means more dynamic and less distorted audio output. 

Dual power modes provide maximum efficiency:

 ADAPT seamlessly 

optimizes the power supply and Class D operating circuitry by adapting to 

the end user’s listening habits. When the ADAPT circuit senses lower signal 

levels, it will automatically optimize the amplifier’s power supply and Class 

D circuitry to a low power mode that maximizes efficiency and minimizes 

heat to almost zero. As a signal increase is detected the amplifier instantly 

shifts into a high power mode, where the power supply and Class D sections 

are now optimized to deliver massive power and headroom for those 

demanding listening sessions. The amplifier is constantly monitoring and 

adapting between these modes which results in higher overall efficiency, 

much lower operating temperatures and rock solid reliability. 

BALANCED DIFFERENTIAL INPUTS

Provides maximum rejection of unwanted noise from upstream 

components. 

AUDIOPHILE NJM2068M OP-AMPS

Most mobile amplifiers today use the standard NJM4558 op-amp which 

has a bandwidth of 3MHz, slew rate of 1V/uSec and noise level of 1.4uV. 

The NJM2068M is simply a better performer with a bandwidth of 19MHz, 

slew rate of 6V/uSec and noise level of .44uV.

The result is quieter, faster and wider bandwidth performance that 

ensures the original music material is reproduced as accurately as 

possible. 

ULTRA HIGH SPEED IR CLASS D CHIPSET

State of the art IR20957 chipset switches at more than 300kHz 

for blistering audio performance. All four or five chipsets are 

sync’d together in unison to eliminate unwanted harmonics or 

distortion. 

POST FILTER FEEDBACK

Feedback is when part of the output signal is “fed back” into the 

original signal to ensure stability and accurate sound. Class D 

amplifiers use output filters (see the 4 vertical coils below), but 

most DO NOT INCLUDE these filters in the feedback loop. Ti2 

amplifiers INCLUDE or take feedback after its passed through 

these filters. The result is more accurate sound that rivals some 

of the best class A/B amplifiers. 

THERMAL ROLLBACK CIRCUIT

Under most conditions, Ti2 amplifiers generate moderate 

to low heat.  However, if extreme conditions exist, as 

temperatures rise the amplifier will automatically adjust the 

power output, so your music continues to play. These changes 

are inaudible and vastly reduce the chance for any thermal 

shutdown events. 

LOW EMI CIRCUIT BOARD DESIGN 

Most class D amplifiers can emit EMI noise that can cause 

problems with AM/FM reception or other devices in the 

vehicle. Ti2 amplifiers have undergone intense real world 

engineering and testing to vastly reduce or eliminate these 

issues. Careful PCB layout using four layers (most amplifiers 

feature just two) along with many key filters ensures a very 

low possibility of any interference issues. 

A

B

C

D

E

F

A

G

B

C

D

E

F

G

Содержание TI2 1000.4













Отзывы: