11
D
Note:
Lead acid gel batteries lose capacity if they are
not charged regularly. The performance and
functionality of the battery depends directly
on the charging pattern. Charge the battery
regularly and always charge the battery fully.
1
Press the power-on button.
During charging, the battery indicator
z
flashes red.
When the battery is fully charged, the
battery indicator will switch off.
D
Note:
The pure water dispenser switches to standby
(power saving) mode after 10 minutes but the
battery continues to charge.
6.1 Other functions
6.1.1 Audio on/off
The pure water dispenser is equipped with an
audible signal that reminds you that dispensing
is in progress. The default setting for this audible
signal is ‘off’. If desired, you can switch on the
audible signal.
1
Power on the Pure Water Dispenser.
Wait till the Dispense button lED starts
flashing (Ready to dispense state - Manual
mode).
2
Press the hold “MUSIC” button.
When you Press the “MUSIC” button te
“During Dispense” audio will be turned ON.
To Switch the audio OFF, press and hold the
“MUSIC” button again.
D
Note:
To perform this operation, make sure that
the Pure Water Dispenser is in the Manual
mode, and the Dispense button LED is
flashing (Ready to dispense).
The Audio ON/OFF setting will change
to default (Factory setting – “AUDIO
OFF”) when the Pure Water Dispenser is
powered on next time.
•
•
•
•
6 Using the appliance
1
Open the tap connected to the pure water
dispenser.
2
When you use the appliance for the first
time or if you have not used the appliance
for 2 days or more, use the PureFlush
function. See section ‘PureFlush’ in this
chapter.
6.0.1 Purifying in manual mode
1
Press the power-on button on the pure
water dispenser
All indicators flash on and off.
The power-on indicator
y
goes on.
Only for model WP3891, the Battery LED
will be off, if the battery is fully charged and
AC supply is available. If battery is being
charged, it would blink red. If the Battery is
at critical stage the battery LED would blink
red, rapidly. In the absence of AC supply
when the battery is in use, the Battery LED
glows constant red.
The pure water dispenser checks the water
availability, the filter and the UV lamp.
As the purification process proceeds, first
the red segment of the purification stage
indicator
e
lights up, followed by the yellow
segment. When the purification process
is finished (after 30 seconds), the green
segment lights up.
The dispense button
d
flashes.
2
Press the dispense button
d
The pure water dispenser dispenses water
and the dispense button lights up green.
3
To stop the water flow, press the dispense
button
d
again.
The dispense button flashes and the
appliance is ready to dispense again.
6.0.2 Charging the battery (type WP3891)
Charge the battery for 1 hours before you use
the pure water dispenser for the first time. After
this, it takes 1 hours to charge the battery fully.
•
•
•
•
•
•
•
•
EN
g
lI
SH
Содержание WP3890
