16
17
AUTO SCAN SETUP
SCAN 01 : AUTOSCAN01
SPEED(MODE) : FAST VECTOR
START ANGLE : 127.1, 027.7 X7
END ANGLE : 157.7, 080.7 X13
SCAN DIR. : CCW
SWAP : OFF
SAVE AND EXIT (ESC TO CANCEL)
HOLD DOWN CTRL KEY
WHILE SELECT POSITION.
3.4 Auto Scan
(First Item of the Main menu / Shortcut:
Scan
)
The Auto scan supports up to 8 programmed angles at user-programmable speeds. Follow these steps to program Auto Scan:
1. Press the
Scan
key to enter Auto Scan menu directly. Or press the
Menu
key to display the main menu on the monitor. Scroll to Auto Scan and push the
Joystick
to the right.
2. Select an Auto Scan number by pushing the
Joystick
left or right.
3. Twist the
Joystick
to enter the title by scrolling through the alphanumeric characters and pushing the handle to the right or left to move to the next space.
Press
Enter
key or push the
Joystick
down to finish title mode. Press
HOME
key in order to delete stored alphanumeric characters.
4. Push the
Joystick
downward to select „Speed” and set the speed by twisting the
Ctrl/PGM
keyclockwise or counterclockwise or moving the
Joystick
left
and right to select the auto scan speed.
5. When finish entering the title and speed, select „START ANGLE” with the
Joystick
. Hold down the
Ctrl/PGM
key while selecting the start position and zoom
using the
Joystick
. Current panning position will be displayed. Release
Ctrl/PGM
key to complete the selection of the start position.
6. Push the
Joystick
downward to select „END ANGLE.” Hold down the
Ctrl/PGM
key while moving the
Joystick
to select the end position and zoom. The
end position angles should be larger than start position. Release the
Ctrl/PGM
key to complete the selection of the end position.
7. Select Save and Exit by pushing the
Joystick
to the right. Press
ESC
to exit the program without saving.
NOTE: Using the Tour mode in conjunction with preset and Auto Scan, you can make the camera travel from one preset position to another preset
position at a specific speed. (Pan only)
a. Before entering the Auto Scan menu, select a preset position as a starting point for Auto Scan.
Example: 2 + Prst
and do step 1 to 4. Instead of step 5, just press the
Ctrl/PGM
key at the start angle position, the current position will be displayed as a
start position.
b. Save and exit from the menu.
c. In normal mode, call a preset to be the end point of scan. Press
3
+
Prst
then press
Scan
key to enter the Auto Scan menu. Move the cursor position to
END ANGLE. Just press
Ctrl/PGM
key at the end angle position. Do step 7.
Example:
Preset 001>002>003>004>005>006, Auto Scan 01 starts at 002, ends at 003, Auto Scan 02 starts at 005, ends at 006. Tour 001, 002, A01, 004,
A02.
1 2 2~3 4 5~6 1 2 2~3 ......
Where : Quick move, ~ : Programmed speed by Auto Scan.
SPEED (MODE):
NORMAL1~NOMAL9, SLOW VECTOR, FAST VECTOR
NORMAL1 (SLOWER) <––> NORMAL9 ( FASTER)
SLOW VECTOR, FAST VECTOR: Move from start point to end point including tilt and zoom simultaneously and linearly.
In case of EDC-143E, EDC-142E1 and EDC-142E2, zoom is fixed at more wide angle and the zoom magnification information is not
displayed.
