Philips Video Camera Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 34

background image

14

15

2.6 Connection

• Connecting to the RS-485/-422

NOTE: Should you experience any control problems when using the Pelco-protocol, connect the ground plate (GND) to the control component.

   The dome camera can be controlled remotely by an external device or control system, such as a control keyboard, using RS-485 half-duplex, RS-422
   duplex or simplex serial communications signals. Connect Marked Rx+, Rx- to Tx+ and Tx- of the RS-485 control system.
   If control system is RS-422, connect Rx+ (Tx+), Rx+ (Tx-) and Rx+, Rx- of the dome camera to Tx+, Tx- and Rx+, Rx- of the control device respectively.
•   Connecting Video out connector
   Connect the video out (BNC) connector to the monitor or video input.
•   Connecting Alarms
   AL1 to 8 (Alarm In)
   You can use external devices to signal the dome camera to react on events. Mechanical or electrical switches can be wired to the AL (Alarm In) and GND
   (Ground) connectors. See Chapter 3 - Program and Operation for configuring alarm input.
   GND (Ground)

NOTE: All the connectors marked GND are common.

   Connect the ground side of the Alarm input and/or alarm output to the GND connector.
   NC(NO)1 TO 4 (Normal Close or Normal Open: Alarm Out)
   The dome camera can activate external devices such as buzzers or lights. Connect the device to the NC(NO) (Alarm Out) and COM (Common) connectors.
   See Chapter 3 - Program and Operation for configuring alarm output.
•   Connecting the Power
   Connect the power of 24VAC 850mA to the dome camera.
   Use certified / Listed Class 2 power supply transformer only.

2.7 Getting Started

Once installed apply power to the dome camera. The dome camera will start a initializing sequence. When configuration is done, the following information is
displayed on the keyboard controller’s LCD.

RAM TEST

CHECK NO. : OK!

CHECK AAAA : OK!
CHECK 5555 : OK!

FASTRAX II E Vx.xxx

CAMERA TYPE xxxx

WAIT DOME SETTING.

INIT TILT ORGIN SET OK
INIT PAN ORGIN SET OK

INIT CAMERA SET OK

001 PRESET

EMPTY DATA !

T001 DOMEID:0001

ALARM:1 W_360.0,090.0

PRESET No.

TITLE

INFORMATION DISPLAY
COMMAND ON WORKING

ALARM DISPLAY

CAMERA TITLE

CAMERA ID

PAN & TILT DEGREE

VIEW DIRECTION

OSD Position

«
...
12
13
14
15
16
...
»

Содержание Video Camera



































Отзывы:

Нет отзывов

Похожие инструкции для Video Camera

Бренд: GE Страницы: 81

Бренд: Hama Страницы: 2

Бренд: T-Eye Страницы: 23

D595 - 5MP Digital Camera

Бренд: Olympus Страницы: 156

Бренд: Olympus Страницы: 148

Бренд: CIS Страницы: 29

Бренд: Takex Страницы: 17

Бренд: Vivitar Страницы: 32

Бренд: Peiying Страницы: 36

Бренд: Ikegami Страницы: 52

20MP Waterproof/ Shockproof Digital Camera

Бренд: Ivation Страницы: 2

CAMEDIA C-480 ZOOM

Бренд: Olympus Страницы: 100

Бренд: ALGE-Timing Страницы: 121

Finepix F750EXR

Бренд: FujiFilm Страницы: 67

Бренд: Quartet Страницы: 29

Бренд: Nauticam Страницы: 29

Бренд: Ricoh Страницы: 208

LUMIX DMC-GF8KGN

Бренд: Panasonic Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды