ENGLISH
IMPORTANT
This baby monitor is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used
as such.
Never leave your baby alone in your home. Always make sure there is
someone present to look after the baby and take care of its needs.
Disclaimer
Please note that you use this baby monitor at your own risk. Koninklijke
Philips Electronics NV and its subsidiary companies are not responsible for
the operation of this baby monitor or your use of it and therefore do not
accept any liability in connection with your use of this baby monitor.
Introduction
Congratulations on your purchase and welcome to Philips Avent! To benefit
fully from the support that Philips Avent offers, register your product at
www.philips.com/welcome
.
This short manual contains important information about your uGrow baby
monitor and offers brief instructions on how to set up the baby monitor
and the app. For more detailed information and the complete user manual,
please visit
www.philips.com/ugrow
.
Important safety information
Read this information carefully before you use the appliance and save it for
future reference.
Danger
- Never immerse any part of the baby monitor in water or any other
liquid. Do not place the appliance where water or any other liquid can
drip or splash onto it. Never use the baby monitor in moist places or
close to water.
- Never put any object on top of the baby monitor and do not cover it.
Do not block any ventilation openings. Install according to
the manufacturer’s instructions.
- Cords present a potential strangulation hazard. Keep cords out of
the reach of children (more than 1 metre/3.5 feet away). Never place
the baby monitor inside or above the baby’s bed or playpen (Fig. 1).
Warning
- Check if the voltage indicated on the adapter corresponds to the local
mains voltage before you connect the appliance.
- Do not modify and/or cut and/or change any part of the adapter,
this causes a hazardous situation.
- Only use Philips recommended adapter.
- If the adapter is damaged, have it replaced with one of the original type
to avoid a hazard.
- Do not open the housing of the baby monitor to prevent an electric shock.
- This appliance is not intended for use by persons (including children)
with reduced physical, sensory or mental capabilities, or lack of experience
and knowledge, unless they have been given supervision or instruction
concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with
the appliance.
- Protect the power cord from being walked on or pinched particularly
at plugs, convenience receptacles, and the point where they exit from
the apparatus.
- Make sure that you install the baby monitor in such a way that its cord
does not obstruct a doorway or passage. Make sure the cord does not
lie on the floor where it presents a tripping hazard.
- Keep the packaging materials (plastic bags, cardboard buffers, etc.)
out of the reach of children, as they are not a toy.
- Keep screws and small items out of the reach of the baby.
Caution
- This baby monitor is intended as an aid. It is not a substitute for
responsible and proper adult supervision and should not be used
as such.
- Make sure the baby monitor and the cord are always out of reach
of the baby (at least 1 metre/3.5 feet away) (Fig. 2).
- Use the appliance at a temperature between 0°C (32°F)
and 40°C (104°F).
- Do not mount the baby monitor on or above the baby’s bed or playpen.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including amplifiers) that produce heat.
- Make sure that your hands are dry when you insert the appliance plug
into the appliance and the adapter into the wall socket.
- If you place the baby monitor on a table or low cabinet, do not let
the mains cord hang over the edge of the table or worktop. People may
trip over cords.
Compliance with standards
- This appliance complies with all applicable standards and regulations
regarding exposure to electromagnetic fields.
- This product complies with the radio interference requirements of
the European Community (Fig. 3).
- Philips Consumer Lifestyle hereby declares that this baby monitor
is in compliance with the essential requirements and other relevant
provisions of Directive 1999/5/EC. A copy of the EC Declaration of
Conformity (DoC) is available online at
www.philips.com/support.
Privacy
Philips believes strongly in protecting the privacy of the personally
identifiable information you share with us through the app. We also believe
it is important to inform you about the use of those data.
Therefore, we encourage you to read the privacy notice in the app carefully.
You can also find information on our privacy policy on our website.
Product overview (Fig. 4)
1 WiFi status light
2 Infrared lights
3 Baby monitor lens
4 Microphone
5 Viewing indicator
6 Nightlight
7 Foot
8 Nightlight button with status indication
9 Lullaby play/pause button with status indication
10 Light sensor
11 Temperature and humidity sensor unit
12 Appliance plug socket
13 Reset button
14 On/off button
15 Wall mounting bracket
16 Adapter
17 Appliance plug
First-time setup
Before you start the set-up procedure, make sure:
- You have wireless Internet access (2.4 GHz WiFi).
- You are close enough to the WiFi router to have a good WiFi signal.
- If you use a WiFi repeater, make sure that your router and your WiFi
repeater have the same SSID and that you use the same password for
the router and the repeater.
- You have the password of your WiFi network at hand. Always connect
the baby monitor to a secure network (see chapter ‘Security and
privacy’ in the user manual available online at
www.philips.com/ugrow
).
- Make sure that your smart device runs on iOS 7 or higher, or Android
4.1 or higher.
1
Download the Philips Avent uGrow Smart Monitor app from
the App Store or Google Play. Use keywords ‘uGrow smart monitor’
or ‘Philips smart monitor’ to find the app.
2
Launch the app.
3
Follow the set-up instructions in the app.
Mounting the baby monitor on the wall
The baby monitor comes with a wall mounting bracket. Before you mount
the baby monitor on the wall, make sure there is a good WiFi signal at the
point where you want to mount the baby monitor. Follow the instructions
below to fasten the wall mounting bracket to the wall and to attach
the baby monitor onto the wall mounting bracket.
1 Use a pencil to put a cross on the wall at the place where you want to
mount the baby monitor. (Fig. 5)
2 Hold the wall mounting bracket to the wall. Make sure that one of
the holes is right over the cross that you put on the wall at step 1.
Note: Make sure that the ring of the wall mounting bracket slants downward
when you hold it to the wall. If the ring of the wall mounting bracket slants
upward, turn the wall mounting bracket the other way around so that it is in
the correct position (Fig. 6).
3 Use a pencil to mark the other screw hole on the wall (Fig. 7).
4 Drill 2 holes in the wall at the marks (Fig. 8).
5 Use 2 screws to fasten the wall mounting bracket to the wall.
Tighten the screws with a screwdriver (Fig. 9).
6 Pass the humidity and temperature sensor unit through the hole in the
wall mounting bracket. Then align the slots in the foot of the baby monitor
with the projections on the ring. Fit the groove in the foot of the baby
monitor onto the raised edge on the inside of the ring (Fig. 10).
7 Turn the foot of the baby monitor clockwise to position the baby monitor
(Fig. 11).
