Philips Saeco Moltio HD8766 Скачать руководство пользователя страница 59

Страница: 59 / 68

ENGLISH

TROUBLESHOOTING

This chapter summarizes the most common problems you could encoun-
ter with your machine.
If you are unable to solve the problem with the information below, visit

www.philips.com/support

for a list of frequently asked questions or

contact the Philips Saeco hotline in your country.
The contact details can be found in the warranty booklet packed sepa-
rately or on

www.philips.com/support.

Machine actions

Causes

Solutions

The machine does not switch on.

The machine is not connected to the
electric network.

Connect the machine to the electric
network.

The power button is on position "0".

Check that the power button is set to "I".

The drip tray gets fi lled although
no water is drained.

Sometimes water is drained automati-
cally by the machine into the drip tray
to manage the rinsing of the circuits
and ensure optimum machine perfor-
mance.

This is seen as normal machine
behavior.

The red

icon is always dis-

played on the machine.

The coff ee grounds drawer has been
emptied with the machine off .

The coff ee grounds drawer must always
be emptied with the machine on. Wait
until the

icon is displayed before

refi tting the drawer.

Coff ee is not hot enough.

The cups are cold.

Preheat the cups with hot water.

No hot water or steam is dis-
pensed.

The hole of the hot water / steam wand
is clogged.

Clean the hole of the steam wand using
a pin.

Make sure that the machine is off and
cold before performing this operation.

Classic Milk Frother is dirty.

Clean the Classic Milk Frother.

Coff ee does not have enough
crema
(see note).

The blend is unsuitable, coff ee is not
freshly roasted or the grind is too
coarse.

Change coff ee blend or adjust the grind
as explained in chapter “Adjusting the
Ceramic Coff ee Grinder”.

The machine takes a long time to
warm up or the amount of water
dispensed from the wand is too
little.

The machine circuit is clogged by
limescale.

Descale the machine.

The brew group cannot be
removed.

The brew group is out of place.

Turn on the machine. Close the service
door. The brew group automatically
returns to the initial position.

The coff ee grounds drawer is inserted.

Remove the coff ee grounds drawer
before removing the brew group.

There is a lot of ground coff ee
under the brew group.

Coff ee is not suitable for automatic
machines.

It may be necessary to change the type of
coff ee or the coff ee grinder settings.

The machine grinds the coff ee
beans but no coff ee comes out.
(see note).

There is no water.

Fill the water tank and prime the circuit
(chapter "Using the Machine for the First
Time").

The brew group is dirty.

Clean the brew group ("Weekly Cleaning
of the Brew Group" chapter).

This might occur when the machine is
automatically adjusting the dose.

Brew a few coff ees as described in chap-
ter “Saeco Adapting System”.

The dispensing spout is dirty.

Clean the dispensing spout.

The circuit is not primed.

Prime the circuit (chapter “Using the
machine for the fi rst time”).

Содержание Saeco Moltio HD8766





































































Результаты поиска

Содержание Saeco Moltio HD8766

Отзывы:

Похожие инструкции для Saeco Moltio HD8766

Бренды по названию

Популярные бренды

Philips Saeco Moltio HD8766, Руководство пользователя

Результаты поиска

Содержание Saeco Moltio HD8766

Отзывы:

Похожие инструкции для Saeco Moltio HD8766

Бренды по названию

Популярные бренды