Alignments
8.
Note:
1.
This function turns enables a monitor to burn in without an
input signal by showing the following burn in pattern cycle:
white, black, red, green, blue.
Hours running
Note:
Power save time is the total time of stand by mode,
suspend mode and off mode.
Factory reset
ADC adjust
Brightness
Color temperature
VT mode
Version
SSC
8.4
Option Settings
Not applicable.
8.5
Software update
8.5.1
Hardware
Connect the cable of RS232 with PC COM port by jump wire.
8.5.2
Firmware
Open the 8051IspWriter.exe. Note the following:
1.
Select File0: select the correct BIOS.
2.
Com Port: Select the correct Port Number.
3.
Click the “ConNect”. It is normal that the picture
disappears. The BIOS is writing now. Please wait a
moment.
4.
Click the “ConNect” button. It shows an error message
when it cannot connect. Recheck if the “Auto program” is
selected and Auto connect didn't select within “Option”.
Double check the port number.
5.
Turn “off” the power if this fails. Remain pushing the reset
button of Winbond Micron. Then turn on the power and
restart from step 3. Release the reset button when BIOS is
writing normal.
Figure 8-2 Factory Mode Indication
Version
Submenu
-
SSC
Submenu
N/A
Setting
Resetable
Default value
Resetable on
Yes
Monitor power on
time
Resetable off
Yes
Power save time
Unresetable on
No
monitor power on
time
Unresetable off
No
Power save time
Setting
Range
Default value
Factory reset
Yes/No
No
Setting
Range
Default value
D sub ADC adjust
Submenu
-
BNC ADC adjust
Submenu
-
YPbPr ADC adjust
Submenu
-
Video ADC adjust
Submenu
-
Setting
Range
Default value
PC max brightness
0 to 255
255
PC min brightness
0 to 255
0
Video max brightness
0 to 255
255
Video min brightness
0 to 255
0
Setting
Range
Default value
Color temperature
-
9300K
User R
0 to 255
255
User G
0 to 255
255
User B
0 to 255
255
Setting
Range
Default value
White
-
0
Red
-
0
Green
-
0
Blue
-
0
Setting
Range
Default value
Version ID
-
-
Setting
Range
Default value
SSC on/off
On/off
On
SSC scan (kHz)
-
80
SSC step (/100)
-
1
SSC DDR
On/off
On
Setting
Range
Default value
I_17540_04
8
.ep
s
3
1010
8
Содержание QCS1.0S
