background image

HD7854/88

Remove back cover.

-  Remove screws (T15) from the back cover.
-  Remove valve outlet.
-  Start at the upper side of the back cover and stick a 

screwdriver between the back cover and lid cover and gently 
pull the back cover from the appliance so that a little chink 
between back cover and lid becomes visible.

-  Put the screwdriver into the 2 rectangular holes (snap locks) 

at the back and gently pull the screwdriver such away that 
the lips of the snap locks are bent outwards.

-  If both clicks positions are loose, it is possible to remove the 

back cover.

-  Reassemble follow steps backwards.

Remove brew chamber:

Removing Brew chamber head handle as follows:
-  Remove boiler from the snap lock position of the brew 

chamber.

-  Gently lift the backside (see picture) of the brew chamber 

up and unhook the two snap locks on front with help of a 
screw driver.

-  Remove connection PCB + PCB cover.
-  Remove 3 way valve and electronic connectors (

U

 & 

Z

from the connection PCB.

-  Reassemble follow above steps backwards.

Remove the “lid closed” detection micro switch.

Disassemble brewing head.
-  Unlock the snap lock which is holding the micro switch 

assembly.  (see picture for detail)

-  Gently pull out the switch assembly.
-  Reassemble follow above steps backwards.

DISASSEMBLY- AND RE-ASSEMBLY ADVISE

Remove brew chamber cover to reach user interface PCB.

-  To remove the brew chamber lid cover place the screwdriver 

on the positions (see picture) and lift the cover over the 
snap locks on both positions.

-  The cover lid can now be lifted a little.
-  Remove the complete cover by unlocking the pushrod from 

the brew chamber.

-  The user interface PCB can be removed by unscrewing 

3 screws (T8)

-  Reassemble follow steps backwards.

Removing the “de-scaling Hall sensor” detector / steam 
connection

-  To be able to remove the Hall sensor, first unhook the spout 

out of the housing.

-  Hall sensor assy can be taken out.
-  To disconnect the steam connector rotate it clockwise and 

pull out of the spout.

To reach the components like pump, PCB, steam heater 
placed on the base.

-  First remove back cover, brew chamber, 3-way valve, steam 

pump and boiler.

-  Remove the 4 Torx T15 screws (two at the base and two at 

the housing part.

-  Bend the 2 click snap locks with a screwdriver (see base), 

the housing can now be removed.

-  To remove the rest of the housing unlock the 4 snap locks at 

the base and gently pull of the front cover.

-  To reassemble follow above steps backwards.

OPTIONAL (accessories)

-  No specific issues

3-11

Содержание HD7854/88












Отзывы: