background image

Published by Philips Consumer Lifestyle 

Printed in the Netherlands 

© Copyright reserved 

Subject to modification

Service Manual

Philips Consumer Lifestyle

Coffeemaker Grind & Brew

15/01

HD7762/00
HD7762/00/C

PRODUCT INFORMATION

Safety

•  This product meets the requirements regarding 

interference suppression on radio and TV.

•  After the product has been repaired, it should function 

properly and has to meet the safety requirements as 
officially laid down at this moment.

TECHNICAL INFORMATION

• Voltage 

: 220-240V

• Frequency 

: 50 Hz

• Power consumption 

: 1000W

•  Color setting 

:  Black / Metal

• Dimensions

 

Appliance  H x W x D 

:  440 x 210 x 310 mm

 

F-Box  L x W x H 

:  320 x 280 x 505 mm

•  Cord length 

:  0,8 m

• Filter size 

: 1x4

• Contents

 Jug 

(max.) 

1320 

mL

 

Water container  (min.) 

:  264 mL  (2 cups)

 

Water container  (max.) 

:  1320 mL  (10 cups)

 

Avg. water loss during brew process  :  10%

• Materials

 Appliance 

PP

 

Metal wrap 

:  Stainless steel

 Jug 

Glass

 Hoses 

Silicon

•  Brew time  (max.) 

:  10 min

•  Temperature  (full jug) 

:  > 80 °C

•  Keep warm time 

:  120 minutes

 

 

:  30 min per WK1501

 

 

  for EU countries only

•  Auto Shut-off time 

:  30 mins

 

 

  (/C version only)

= changed

Содержание HD7762/00
















Отзывы: