MasterColor
®
Pulse Start Ceramic Metal Halide 350 Watt ED-37 (Clear) Lamp
featuring
ALTO
®
LampTechnology
Electrical Data
(Subject to change without notice)
Lamp Watts (Nominal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350
Lamp Operating Voltage (rms) (Nominal)
2
. . . . . . . . . . . . 150
Initial Lamp Voltage Range (rms)
3
. . . . . . . . . . . . . . . . . . . . 135-165
Lamp Operating Current (Amps) (rms) (Nominal) . . . . . 2.83
Lamp Current Crest Factor (Maximum) . . . . . . . . . . . . . . 1.6
Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . . . 5 Minutes
Restrike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . . . . . . 15 Minutes
Ballast Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI M171/M131/O
Ballast Open Circuit Voltage (Minimum). . . . . . . . . . . . . . . 254 RMS Min.
Pulse Peak Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3000 Minimum, 4000 Maximum
Pulse Width @ 90% Peak (2700 Volts) . . . . . . . . . . . . . . . . 1.3 Micro Second Minimum
Pulse Repetition Rate (Minimum) . . . . . . . . . . . . . . . . . . . . 1 per Half Cycle
Minimum Operating Temperature . . . . . . . . . . . . . . . . . . . . -30º C (-22°F)
1) Measured at 100 hrs of life in vertical position.
2) Measured at rated lamp watts on a linear reactor. LPW does not include ballast losses.
3) Measured with the lamp operating at rated watts.
Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
A Division of Philips Electronics North America Corporation
Updated 5/07
TDS-132571
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
A Division of Philips Electronics Ltd.
www.philips.com
Warnings, Cautions and Operating Instructions
R
“WARNING:
These lamps can cause serious
skin burn and eye inflammation from short wave
ultraviolet radiation if outer envelope of the lamp is
broken or punctured. Do not use where people will
remain for more than a few minutes unless adequate
shielding or other safety precautions are used. Certain
lamps that will automatically extinguish when the outer
envelope is broken or punctured are commercially
available.”This lamp complies with FDA radiation
performance standard 21 CFR subchapter J.
(USA:21CFR 1040.30 Canada:SOR/DORS/80-381)
If the outer bulb is broken or punctured, turn off
at once and replace the lamp to avoid possible
injury from hazardous short wave ultraviolet
radiation. Do not scratch the outer bulb or subject
it to pressure as this could cause the outer bulb to
crack or shatter.A partial vacuum in the outer
bulb may cause glass to fly if the envelope is struck.
WARNING:
The arc-tube of metal halide lamps
are designed to operate under high pressure and at
temperatures up to 1000º C and can unexpectedly
rupture due to internal or external factors such as a
ballast failure or misapplication. If the arc-tube ruptures
for any reason, the outer bulb may break and pieces of
extremely hot glass might be discharged into the
surrounding environment. If such a rupture were
to happen,
THERE IS A RISK OF PERSONAL
INJURY, PROPERTY DAMAGE, BURNS
AND FIRE.
These lamps are designed to retain all the
glass particles should an arc tube rupture
occur.The following operating instructions are
recommended to minimize these occurrences.
RELAMP FIXTURES AT OR BEFORE THE END
OF RATED LIFE.Allowing lamps to operate
until they fail is not advised and may increase
the possibility of inner arc tube rupture.
This lamp contains an arc tube with a filling
gas containing Kr-85 and is distributed by
Philips Lighting Company, a division of Philips
Electronics North America Corporation,
Somerset, New Jersey, 08875.
CAUTION:
TO REDUCE THE RISK OF PERSONAL
INJURY, PROPERTY DAMAGE, BURNS AND FIRE
RESULTING FROM AN ARC-TUBE RUPTURE
THE FOLLOWING
LAMP OPERATING
INSTRUCTIONS
MUST BE FOLLOWED:
LAMP OPERATING INSTRUCTIONS:
1. RELAMP FIXTURES AT OR BEFORE THE END OF
RATED LIFE. Allowing lamps to operate until they fail is
not advised and may increase the possibility of inner arc
tube rupture.
2. Before lamp installation/replacement, shut power off and
allow lamp and fixture to cool to avoid electrical shock
and potential burn hazards.
3. Use only auxiliary equipment meeting Philips
and/or ANSI standards. Use within voltage limits
recommended by ballast manufacturer.
A. Operate lamp only within specified limits of operation.
B. For total supply load refer to ballast manufacturers
electrical data.
C. All Pulse Start mogul based lamps require a socket
rated to withstand a 4000 volt pulse.
4. Periodically inspect the outer envelope. Replace any
lamps that show scratches, cracks or damage.
5. If a lamp bulb support is used, be sure to insulate the
support electrically to avoid possible decomposition of
the bulb glass.
6. Protect lamp base, socket and wiring against moisture,
corrosive atmospheres and excessive heat.
7. Time should be allowed for lamps to stabilize in color
when turned on for the first time. This may require
several hours of operation, with more than one start.
Lamp color is also subject to change under conditions
of excess vibration or shock, and color appearance may
vary between individual lamps.
8. Lamps may require 10 to 20 minutes to re-light if there
is a power interruption.
9. Take care in handling and disposing of lamps. If an
arc tube is broken, avoid skin contact with any of the
contents or fragments.
10. Use this lamp only in fixtures that contain Pulse Start
metal halide ballasts and are specifically designed for
use with Pulse Start metal halide lamps.
WARNINGS, CAUTIONS AND OPERATING INSTRUCTIONS for Protected MasterColor
®
Pulse Start
Ceramic Metal Halide Lamps (Vertical Operation ± 15°, Open or Enclosed Fixtures )
