background image

WeaKnees.com

http://www.weaknees.com/

2.4.

 

Using your larger Torx screwdriver, unscrew and remove the two screws on

the left-hand side of the drive bay (as you are looking at the front of the TiVo). Also
remove the gold inserts from the blue grommets and keep the two screws inside the gold-
colored inserts.

2.5.

 

Once the screws and inserts are removed, you will be able to lift the drive

bay up from the left side and slide it out of the two holes on the right side of the drive
bay. As you slide the drive bay up and out of the holes, watch the drive cable and power
cable that are connected to the drive. Flip the drive bay up and out of the TiVo and onto
the TiVo lid, with the hard drive face-down on the TiVo lid and the two cables running
from the drive to the TiVo. You will now need to remove both of the cables connected to
the hard drive by following the instructions below:

(a)

 

The hard drive has a power connector running into the hard drive. The

power cable has a white connector plugged into the hard drive. Remove the power
connector from the hard drive. The power cables are sometimes difficult to remove;
patience and wiggling it back and forth usually does the trick.

(b)

 

Remove the hard drive ribbon cable (longer, gray cable with a blue or

black connector) from the hard drive by pulling on the hard plastic piece connected to the
hard drive.

3.

 

FIXING THE JUMPER

Pick up the hard drive bay and look at the hard drive with the label facing up and
the empty power/IDE cable connectors facing you. Your TiVo’s hard drive has a
small white plastic “jumper” that is located between the IDE cable and the power
cable connectors.

You will notice a total of four pairs of pins (and, therefore, 4 possible places for the
jumper). Ignore the single pin located closest to the IDE cable.

In a Maxtor hard drive, the jumper should be moved to the furthest left-hand
position (again, ignoring the single pin). Gently remove the jumper with the end of
a paper clip or your fingernail and move it to the proper position. NOTE: the jumper
must be vertical and must be carefully inserted so that the jumper fits inside the
left-hand most pins.

4.

 

MOVING THE EXISTING DRIVE

4.1.

 

After you have moved the jumper to the proper setting, place the hard drive

bay upside-down on the TiVo lid, with the drive label down and the drive connectors
facing the front of the TiVo.

4.2.

 

With the hard drive bay upside down on the TiVo lid, use your larger Torx

screwdriver and remove the four screws connecting the hard drive to the hard drive bay.
Do not confuse these screws with the four screws you removed from the back of the TiVo
before removing the lid.

Содержание DSR6000







Отзывы: