3-3
PCS 101 017
3-3
PLAY
Button pressed?
Y
N
Set is in Service PLAY Mode.
The CD PLAY is intended to
detect intermittent or not reproducible failures.
This is done by continuously playing a disc.
In case of failures, error codes according
to table 2 will be displayed.
SERVICE
PLAY MODE
This mode is intended for
- CD PLAY Test
Table 2
Error code
E1000
E1001
E1002
E1003
E1005
E1006
E1007
E1008
E1020
E1070
E1071
E1079
F = Fatal error & the set stop play function W = Warning
Error Description
Focus Error
Triggered when the focus lost for a certain time during play.
Radial Error
Triggered when the radial servo is not on track for a certain time during play.
Sledge In Error
The sledge did not reach its inner position (inner-switch is still close) before approximately 6 Sec. have
passed by. Inner-switch or sledge motor problem.
Sledge Out Error
The sledge did not come out of its inner position (inner-switch is still open) before approximately 250 mSec.
have passed by. Inner-switch or sledge motor problem.
Jump error
Triggered in normal play when the jump destination could not be found within a certain time.
Subcode Error
Triggered when a no valid subcode for a certain time during play.
PLL Error
The Phase Lock Loop could not lock within a certain time.
Turntable Motor Error
Generated when the CD could not reached 75% of speed during startup within a certain time. Discmotor problem.
Focus Search Error
The focus point has not been found within a certain time.
The carousel switch is not open within certain time. This can happen when either the switch is defective and
closed all the time, or when the carousel is blocked in between two disc positions.
The time-out is approximately 5 seconds.
The carousel position switch did not close within a certain time. This can happen when the switch is defective
and never closes electrically, or when the carousel is blocked in between two disc positions. The time-out is
approximately 5 Sec.
The drawer could not enter the inside position and is opening again. This can be caused because the drawer is
blocked by something and cannot go fully inside, or the drawer switch is defective and does not close.
Type
W
W
W
W
W
W
W
W
F
W
W
W
NEXT Button
pressed?
Y
N
FOR CD Test
see page 3-4
CD
TEST
PROGRAM
Button pressed?
Y
Y
N
N
STOP
Button pressed?
Display shows
8M
Output at (Front Board)
pin 80 of uP = 1,953.125Hz
QUARTZ
TEST
Y
N
Y
N
Y
N
TIME
Button pressed?
TIME
Button pressed?
DISPLAY
TEST
Display shows
Figure 1
Display shows
Figure 2
Figure 1
TRACK
PEAK
TOT
REM
TRACK
TIME
SHUFFLE
PAUSE
REPEAT DISC
PROGRAM
5
4
1
3
2
1
FTS
VIDEO CD -I
+
G
Figure 2
TRACK
TOT
TRACK
SHUFFLE
REPEAT DISC
CD
+
G
STOP
Button pressed?
To start service test program
hold STOP & PLAY
depressed while
plugging in the mains cord
Display shows the
ROM version *
"S V yy"
(Main menu)
S refers to Service Mode.
V refers to Version.
yy refers to Software version number of
µ
Processor.
(Counting up from 01 to 99)
SERVICE TEST PROGRAM I
MAIN MENU
Y
N
Y
N
Y
N
SHUFFLE
Button pressed?
Any Button
pressed?
KEY TEST
Display shows "
--
"
Display according
to Table 1
Table 1
Keys
activated
No Key pressed
Any Remote control key
Program
Scan
Repeat
Edit
Time
Fader
Display
shows
--
RC
1
2
3
4
5
6
Keys
activated
Pause
Previous
Next
Stop
Play
Shuffle
Disc 1
Disc 2
Keys
activated
Disc 3
Disc 4
Disc 5
Open/Close
Quick Play
Load
Display
shows
7
8
9
Exit
11
12
13
14
Display
shows
15
16
17
18
19
20
STOP
Button pressed?
