English
Controls/Power Supply
Congratulations on your purchase and
welcome to Philips!
To fully benefit from the support that
Philips offers, register your product at
www.philips.com/welcome.
Supplied Accessories
– AC power cord
– Line-in cable
Top/front panels (See
1
)
1
Source selector
:
CD/MP3/AUX
,
FM
,
MW or OFF
– selects CD/MP3, AUX, FM or MW source of
sound
– power off switch
2
2;
– starts or pauses CD/MP3 playback
§ ∞
– selects the next/previous track
– fast searches forwards/backwards
(press and hold the button)
PROG
– programs tracks
9
– stops CD playback;
– erases a CD program
3
Display
– shows the CD functions
4
MODE
– selects different play modes:
e.g. REPEAT or SHUFFLE (random
order)
5
ALBUM +
– For MP3-CD only: selects
albums
6
OPEN•CLOSE
– opens/ closes the CD
door
7
TUNING
– tunes to radio stations
8
VOLUME
– adjusts volume level
Back/bottom panels (See
1
)
9
Telescopic antenna
– improves FM
reception
0
Battery door
– open to insert 6 x 1.5V
R-14
/
UM-2
/
C-cells
!
AUX IN jack
– connects an external source
(3.5 mm socket)
@
AC MAINS~
– inlet for power cord
#
Voltage selector
– adjust to match the
local voltage 110/220V before plugging in the
set
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in unsafe
operation.
Power Supply
Whenever convenient, use the power supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1
Open the battery door and insert 6 batteries,
type
R-14
,
UM-2
or
C-cells
, (preferably
alkaline) with the correct polarity as indicated
by the "
+
" and "
–
" symbols inside the com-
partment (See
1
).
2
Replace the battery door, making sure the bat-
teries are firmly and correctly in place.The set
is now ready to operate.
Power Supply
Basic Operation/ Radio/AUX
• Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst
:
• Do not mix battery types: e.g. alkaline with car-
bon zinc. Only use batteries of the same type
for the set.
• When inserting new batteries, do not try to mix
old batteries with the new ones.
• Remove the batteries if the set is not to be used
for a long time.
Batteries contain chemical substances, so
they should be disposed of properly.
Using AC power
1
Check if the power voltage,
as shown on
the type plate located on the
bottom of the set,
corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2
If your set is equipped with a voltage selec-
tor, adjust the selector so that it matches
with the local power supply.
3
Connect the power cord to the
AC MAINS~
inlet and the wall socket.The
set is now connected and ready for use.
4
To switch the set off completely, withdraw the
power cord from the wall socket.
5
Install the unit near the AC outlet and where
the AC power plug can be easily reached.
•
Disconnect the power cord from the wall
socket to protect your set during heavy
thunderstorms.
The type plate is located on the
bottom of the set.
Helpful hints:
–
To avoid unnecessary energy consumption,
always adjust the
Source selector
to
OFF
after using the set.
Basic operation
Switching on and off and selecting the
function
1
To select your sound source, adjust the
Source selector
to:
CD/MP3/AUX
,
FM
,
or
MW
.
2
To switch off the set, adjust the
Source selector
to
OFF
position.
Adjusting volume
Adjust the sound with the
VOLUME
control.
Radio reception
1
Adjust the
Source selector
to
FM
or
MW
to select your desired waveband.
2
Turn
TUNING
to tune to a station.
Helpful hints:
To improve radio reception
•
For
FM
, extend, incline and turn the telescop-
ic antenna for best reception. Reduce its
length if the signal is too strong.
•
For
MW
, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
Connecting an external device
You can listen to the sound of the connected
external device through your AZ1134’s
speakers.
1
Adjust the
Source selector
to
CD/MP3/AUX
.
2
Use the supplied line-in cable to connect
AZ1134’s AUX IN jack (3.5 mm, located on
the panel panel) to an AUDIO OUT or
headphone jack on an external equipment
(such as CD player or VCR).
➜
AUX mode will auto switch on to play the
sound, overriding the active CD or mode.
ifu_az1134_55_eng 5/26/08 14:01 Page 4
