English
Controls/Power Supply
Supplied accessories
AC mains lead
Top and front panels (See
1
)
1
VOLUME
– adjusts volume level
2
Source selector
:
CD, TUNER,
TAPE/
POWER OFF
– selects CD, tuner or tape source of sound
– power off switch
3
CD door
4
TUNING
– tunes to radio stations
5
BAND
– selects waveband
6
PREVIOUS, NEXT
∞
,
§
– skips or searches a passage/track
backwards or forward
7
PROG
– programs and reviews
programmed track numbers
8
Cassette recorder keys:
;
– pauses playback or recording
9/
– stops the tape;
– opens the cassette holder
5
or
6
– fast winds/ rewinds tape
1
– starts playback
0
– starts recording
9
Cassette door
0
CD Display
– shows the CD functions
!
PLAY/PAUSE
2;
- starts or pauses CD
playback.
@
STOP
9
– stop playback;
– erases a CD program.
Back panel
#
Telescopic antenna
- improves FM
reception.
$
Battery door
- open to insert 6 x 1.5V
R-14
/
UM2
/
C-cells
.
%
AC MAINS
- inlet for power cord
CAUTION
Use of controls or adjustments or
performance of procedures other
than herein may result in hazardous
radiation exposure or other unsafe
operation.
Power Supply
Whenever convenient, use the mains supply
cord if you want to conserve battery life.
Make sure you remove the plug from the set
and wall outlet before inserting batteries.
Batteries (not included)
1
Open the battery compartment and insert
six batteries, type
R-14
,
UM-2
or
C-cells
,
(preferably alkaline) with the correct polarity
as indicated by the "
+
" and "
–
" symbols inside
the compartment. (See
1
)
2
Replace the compartment door, making sure
the batteries are firmly and correctly in place.
The set is now ready to operate.
Batteries contain chemical substances, so
they should be disposed of properly.
Power Supply
General operation/Radio
• Incorrect use of batteries can cause
electrolyte leakage and will corrode the
compartment or cause the batteries to burst:
• Do not mix battery types: e.g. alkaline with
carbon zinc. Only use batteries of the same
type for the set.
• When inserting new batteries, do not try to
mix old batteries with the new ones.
• Remove the batteries if the set is not to be
used for a long time.
Using AC Mains
1
Check if the power/mains voltage,
as shown
on the type plate located on the
bottom of the set,
corresponds to your
local power supply. If it does not, consult your
dealer or service center.
2
Connect the power cord to the AC
POWER/MAINS inlet and the wall socket.
The mains lead is now connected and ready
for use.
3
To switch the set off completely, withdraw the
power cord from the wall socket.
•
Disconnect the mains lead from the wall
socket to protect your set during heavy
thunderstorms.
Helpful hints :
To avoid unnecessary energy
consumption, always adjust the
source
selector
to
TAPE/
POWER OFF
after using
the set. Also check that the tape deck keys
are released
The type plate is located on the bottom
of the set.
General operation
1
To select your sound source adjust the
source selector
to :
CD
,
TUNER
or
TAPE/
POWER OFF
.
2
Adjust the sound with the
VOLUME
control.
3
To switch off the set, adjust the source selec-
tor to
TAPE/
POWER OFF
position and check
the cassette keys are released.
Radio reception
1
Adjust the
source selector
to
TUNER
.
2
Adjust
BAND
to select your desired
waveband, FM or AM.
3
Turn
TUNING
to tune to a station.
•
For
FM
, extend and turn the telescopic
antenna for best reception. Reduce its length
if the signal is too strong.
•
For
AM
, the set uses a built-in antenna.
Direct this antenna for best reception by
turning the whole set.
4
To switch off the radio, adjust the source
selector to
TAPE/
POWER OFF
position and
check the cassette keys are released.
