8
Executing Playback:
1.
Press ON, AUX 50, ENTER for continuous playback.
2.
Press ON, AUX 51, ENTER for single playback.
Stopping Playback:
1.
Press Off, AUX 50 or AUX 51, ENTER or move
joystick.
Resuming Playback After Stopping During Playback:
1.
After stopping during playback, press On, AUX 52,
ENTER.
Note: If you have moved the AutoDome since stopping, playback will
resume where playback was previously stopped.
Adding To Previously Recorded Playback:
1.
Execute a single playback.
2.
Wait for the playback to end.
3.
Press On, AUX 101, ENTER.
4.
Begin controlling the AutoDome.
5.
At the completion of controlling the AutoDome, press
Off, AUX 100 or AUX 101, ENTER.
Changing Ending of Previously Recorded Playback:
1.
Execute a single playback.
2.
Wait for the playback to reach the point where the
change is desired.
3.
Press Off, AUX 50 or AUX 51, ENTER to stop
playback. This step is optional.
4.
Press On, AUX 101, ENTER
5.
Begin controlling the AutoDome.
6.
At the completion of controlling the AutoDome, press
Off, AUX 100 or AUX 101, ENTER.
Erasing A Playback From Some Point
In Playback To The End:
1.
Execute a single playback.
2.
Wait for the playback to reach the new stopping
position.
3.
Press Off, AUX 50 or AUX 51, ENTER.
4.
Press Set, AUX 500, ENTER.
DIP Switches
S2005.1, S2005.2, and S2005.3: These DIP switches
are used to set both the pan and tilt speeds when the
dome is being controlled by a system generating "fixed-
speed" commands. The table below lists the maximum
speeds when the zoom lens is set for full wide angle.
The speed automatically decreases from the maximum
speed as the lens is adjusted towards the telephoto
settings. At its full telephoto setting, the speed will be
decreased to approximately 12% of its full wide angle
speed.
DIP Switch Settings
Maximum Speed
1
2
3
(°/s)
Off
Off
Off
4
On
Off
Off
6
Off
On
Off
10
On
On
Off
15
Off
Off
On
20
On
Off
On
30
Off
On
On
45
On
On
On
60
If the auto-speed feature is enabled (see DIP switch
S2005.4), these DIP switches apply only to the tilt speed.
S2005.4: This switch controls the Auto-speed feature.
When on, auto-speed is always enabled and control by
AUX 16 is ignored; see Auto-Speed (AUX 16) under
SETUP & MAINTENANCE in TC700 Series Camera,
Lens, Pan/Tilt, and Receiver/Driver Modules User’s
Manual (TC700-UM) for description. When auto-speed
is enabled, the pan speed starts out slowly and
increases as the pan control is held on. The speed
resets to slow when the pan control is released. The tilt
speed is not affected by this switch. It is still controlled by
the setting determined by DIP switches S2005.1,
S2005.2, and S2005.3. The auto-speed feature is only
applicable when the dome is being controlled by a
system generating “fixed speed” commands.
S2006.1: RS-232 Baud rate: 2400 - OFF, 9600 - ON
S2006.2: Lens Zoom Polarity
S2006.3: Lens Focus Polarity
S2006.4: Lens Iris Polarity
S2007.1: Not defined, set to OFF
S2007.2: Not defined, set to OFF
S2007.3: Not defined, set to OFF
S2007.4: Not defined, set to OFF
S2008.1: Reserved, set to OFF
S2008.2: Reserved, set to OFF
S2008.3: Reserved, set to OFF
S2008.4: Not defined, set to OFF
Thumbwheel Switch
As Address selector, 0000 responds to all messages
regardless of address; otherwise the unit will only
respond to commands issued for that address.
Camera Commands
Adjustable Phase Vertical Line Lock (AUX 41)
In multicamera systems using vertical interval switchers,
it is desirable to have the video output signals from all
cameras vertically synchronized. To achieve synchro-
nization, it may be necessary to generate phase delays
in some cameras, especially if the cameras receive
power from different phases of a 3-phase power source.
As shipped from the factory, camera vertical sync is
aligned with the positive-going zero crossing of the hot
