7
Camera - Using Auxiliary Controls
Camera
Function
Aux
No.
Description
On/Off
Notes
BL_COMP
20
Backlight
Compensation
On/off
1
HIGH-LIGHT
21
Highlight
On/off
1, 7
SHUTTER_ADJ
22
Shutter Adjust
Inc/dec
1
SHUTTER
23
Shutter
On/off
1
WHITE_BALANCE
30
White Balance
Auto/
manual
8
RED
31
Red Adjust
Inc/dec
1, 8
BLUE
32
Blue Adjust
Inc/dec
1, 8
R_Y_HUE
33
R-Y Hue Adjust
Inc/dec
3, 8
B_Y_HUE
34
B-Y Hue Adjust
Inc/dec
3, 8
FIXED_WB
35
Fixed
White Balance
Indoor/out
door
1, 8
FACTORY_
DEFAULTS
40
Factory Default
Settings
Set/---
1,3
LL_PHASE
41
Adjust LL Phase
Delay
Inc/dec
3
SYNC
42
Sync Mode
ll/xtal
3
AGC
43
AGC
On/off
3
Note: Auto-pan is discontinued when the manual pan
control (joystick) is used.
Auto-iris and auto-focus revert to manual mode when the
manual iris and focus controls are used, respectively.
Switching to manual iris or manual focus from auto mode
reverts to the last manual setting used.
Auto-focus is activated automatically upon pan or tilt
when Auto-focus Activation is on (AUX #12).
Manual iris is activated automatically upon activating
(ON) Backlight Compensation.
Commands Using Pre-Position Controls
Receiver/Driver
Function
Pre-
Position
No.
Description
SET/SHOT
Notes
Pre-position
1-60
---
Set/show
4
Future
PP Expansion
61-100
---
----/----
--
Auto-pan
left limit
101
---
Set/show
2
Auto-pan
right limit
102
---
Set/show
2
Home Position
110
---
Recalibrate/
show
--
Disable/Enable
PP
901-960
---
Disable/
enable
6
Global Disable/
Enable PP
900
---
Disable/
enable
6
Notes:
1.
The following settings are stored with pre-position
scenes:
Pan position.
Tilt position.
Zoom position.
Focus mode AUTO/MANUAL.
Focus position for MANUAL mode.
Iris mode AUTO/MANUAL.
Iris ALC/LEVEL for AUTO mode or position for
MANUAL mode.
White Balance mode AUTO/MANUAL (color
cameras only).
Red content and Blue content for MANUAL
mode (color cameras only).
Shutter mode ON/OFF.
Shutter setting for ON mode.
Backlight compensation ON/OFF.
Highlight ON/OFF (monochrome cameras only).
2.
The following settings are stored as a default setting
in nonvolatile memory (EEPROM) on R/D board and
are used to restore settings at power-up:
Auto-pan left limit = 0 degrees.
Auto-pan right limit = 359.9 degrees.
Auto-pan speed = 30 degrees per second.
Auto-focus activation = ON.
Auto-iris activation = ON.
Auto-speed = OFF.
3.
This setting stored as a default setting in nonvolatile
memory in camera.
4.
Pre-position #1 (if set) is automatically called-up
upon power-up just after the homing sequence.
5.
Scan direction determined by last manual pan
direction.
6.
Pre-positions can be disabled such that they do not
operate during pre-position tour. They are still
available for manual call-up.
7.
Applies to monochrome cameras only.
8.
Applies to color cameras only.
Auto-Playback
Applicable only to units fitted with this feature.
Recording Playback:
1.
Position AutoDome to the point where playback is to
start.
2.
Press On, AUX 100, ENTER.
3.
Begin controlling the AutoDome.
4.
At the completion of controlling the AutoDome, press
Off, AUX 100, ENTER.
Note: If you run out of record time prior to issuing the stop record
command, the AutoDome will position itself at the beginning and
not move until the joystick is released for one second.
