Philips Antumbra Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 31

background image

13 October, 2017

Antumbra

17

Installation

2.2

Installation Procedure

The following installation procedure applies to all Antumbra panel variants.

Antumbra panels are powered from the DyNet network, which is classified as SELV/Class II
(for NA) Overvoltage category III in accordance with IEC60664-1(0.8 kV surge).

Ensure that installation of the Antumbra Panel is in compliance with HD 60364 - 4I where
applicable.

Caution:

Use approved DyNet power supplies only with incorporated overload protection.

Disconnect DyNet before attaching the communication module to the application module.

2.2.1

Base Unit Installation

The communication module and application module lock in together when the locating pin
on the Application module lines up with the locating socket on the communication module
(circled below).

«
...
15
16
17
18
19
...
»

Содержание Antumbra
































Отзывы:

Нет отзывов

Похожие инструкции для Antumbra

Бренд: Hamworthy Страницы: 10

Бренд: Samson Страницы: 92

Бренд: Jafar Страницы: 10

Бренд: 7bit Страницы: 2

Бренд: Jafar Страницы: 15

Бренд: Barco Страницы: 6

Бренд: Saga Страницы: 9

Бренд: CAME Страницы: 2

Бренд: V2 Страницы: 12

NORA-W10 Series

Бренд: u-blox Страницы: 56

Бренд: z21 Страницы: 2

Бренд: Partizan Страницы: 7

Бренд: OJ Electronics Страницы: 8

Бренд: FUTABA Страницы: 8

Бренд: Vertiv Страницы: 2

Бренд: Quantum Страницы: 20

Бренд: HEIDENHAIN Страницы: 257

Бренд: ECKELMANN Страницы: 147

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды