Philips 50 T Series Скачать руководство пользователя страница 81 | Manualshive

Страница: 81 / 105

background image

Transmitter Functional Blocks

Chapter 9 - Theory of Operation

delivered to the FSK Generator. The detector algorithm is identical to the
algorithm implemented in the Series 50 Fetal Monitors.

FMP is switched off whenever a Series 50 T Telemetry System (plugged into
the Monitor) is switched on. FMP is switched back on again when the
telemetry system is switched off (or unplugged). If you want to monitor FMP
with a Series 50 T Telemetry System (and have the correct software revision
and interface for Telemetry FMP) switch FMP on by using either the Key or
the barcode method.

Modes

This module checks for connected transducers at the Cardio and Toco
connectors. If a valid transducer is detected, the corresponding operating
modes are set in the Transmitter (ECG/US, TOCO/IUP) and the mode
encoding bits are delivered to the FSK signal generator. If an invalid
transducer is detected, these bits are set to an error code and the Transmitter
frontends are disabled.

Toco Driver

This circuitry drives a connected Toco or IUP transducer with a 1.6 kHz, 5V
peak square wave. The 1.6 kHz frequency is synchronised with the 3.2 kHz
repetition rate of the doppler ultrasound circuitries to avoid interference
between the Toco and ultrasound channels.

Toco Receiver

This module contains a differential intput amplifier, a synchronous
demodulator and a low pass filter, to derive a pressure proportional signal
from the TOCO/IUP transducers bridge.

Toco A/D

The TOCO/IUP pressure signal is A to D converted by a sigma-delta type
converter with a resolution of 12 bits and a 2Hz low pass characteristic. The
repetition rate is 4/sec. These 12 bits are encoded in the serial bitstream by
the FSK Generator module.

To ensure a high accuracy of the Toco pressure signal, correction factors are
stored in a EEPROM during the production test individually for every
Transmitter. Before encoding the Toco pressure values into the serial
bitstream, the pressure values are corrected with these factors. This
mechanism allows the usage of circuitries in the Toco frontends which only
have stability over temperature and aging but not an absolute accuracy.

FSK Generator

The Frequency Shift Key generator (FSK), is a sine wave generator (smoothed
square wave by filters) capable of generating either a frequency of 1.6 kHz
(represents a logic zero) or 2.4 kHz (represents a logic one). It encodes the
following signals in a bitstream:

•

Coding pattern identification

•

Transmitters Serial Number

•

12 Bit Toco pressure value

«
...
79
80
81
82
83
...
»

Содержание 50 T Series










































































































Отзывы:

Нет отзывов

Похожие инструкции для 50 T Series

Бренд: Jabra Страницы: 13

Бренд: MartinLogan Страницы: 42

Бренд: Fender Страницы: 12

Бренд: QSC Страницы: 10

Бренд: Toa Страницы: 16

Бренд: Polk Audio Страницы: 10

Бренд: Play Art Multimedia Handels Страницы: 30

Sonic Mobil 160

Бренд: Hama Страницы: 20

Бренд: Bijela Страницы: 10

Бренд: Beta Three Страницы: 10

Бренд: QMotion Страницы: 16

Stadia 100 LA Series

Бренд: Outline Страницы: 12

Бренд: Benwin Страницы: 7

Бренд: Polk Audio Страницы: 5

Бренд: TDT Страницы: 6

Expedition XP106

Бренд: Samson Страницы: 20

Бренд: JAMO Страницы: 9

Бренд: JBL Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды