!
102 Meridian 3
Color
gamut
:
70%
(Typ.)
Gate IC : N/A
Source IC : N/A
Response time : Tr + Tf <=5 ms (Typ)
Vertical
frequency
range
:
56~76Hz
CMI
Type
NR.
:
CMI
M236H3
LA3
Resolution
: 1920 x 1080 (WSXGA+)
Outside dimensions
: 544.8(H) x 320.52(V) Typ. x 11.4(D) Typ.
Pitch
(mm) :
0.2715mm
x
0.2715mm
Color pixel arrangement
: RGB vertical stripe
Display surface
: Hard coating (3H)
Color
depth :
16.7M
(6
bit
Hi-FRC)
Backlight
: LED
Active area (W x H)
: 521.28(H) x 297.22(V) mm
View angle (CR=10)
: =170 for Right/Left (Typ)
:
=160
for
Up/Down
(Typ)
Contrast
ratio
:
1000:1
(Typ)
White luminance
: 300(Typ.)
Color Gamut
: 70% (Typ.)
Gate IC : N/A
Source IC : N/A
Response time : Tr + Tf <=5 ms (Typ)
Vertical
frequency
range
:
56~76Hz
Scanning frequencies
Hor.
: 30 – 83 K Hz
Ver.
: 56 - 76 Hz
Video dot rate: < 210 MHz for VGA and < 170 MHz for DVI, warning message must be displayed while over 165
MHz (supplier to provide accurate scaler bandwidth number)
Power input: 90-264 V AC, 50/60
r
2 Hz
Functions:
(1) D-SUB analog R/G/B separate inputs, H/V sync separated, Composite (H+V) TTL level,
(2) SOG sync : a. Sync select: H + V
b. Sync select: SERR
(3) DVI digital Panel Link TMDS inputs, HDCP supported.
Ambient temperature: 0
q
C - 40
q
C
Power Range
Full Range Power Supply 90 – 264 VAC
Electrical characteristics
Scaler should be capable of below items.
1) Scaler must support color engine for Image enhancement feature (SmartImage)
2) Scaler must have enough memory to support PerfecTune feature and Philips OSD
3) Scaler must support SmartContras,500K:1 DCR preferred
4) VGA signal Auto adjustment:
Monitor automatically adjusts and optimizes resolution and frequency based on input signal defined by
“Source” function. “NO VIDEO INPUT” message to be displayed on screen while no signal is detected. Monitor
will automatically optimize resolution and frequency whenever connected to different signal source. When
press the “Auto”, the screen also show a status bar. During adjustment period, a status bar will show on screen
from 0% to 100% to indicate the progress of adjustment.
Auto adjustment: new timing & preset modes (non- factory preset mode) should do auto adjustment at first time
detection and save the related date into memory. Resolution
ʀ
800x600 , do not do auto adjustment.
Interface signals
1). D-Sub Analog
Input signal
: Video, Hsync., Vsync
Video
: 0.7 Vp-p, input impedance, 75 ohm @DC
Sync.
: Separate sync TTL level , input impedance 2.2k ohm terminate
Hsync Positive/Negative
Содержание 247E3LHSU/00
