Philips 221P3LPEB/00 страница 82 Скачать руководство пользователя

Страница: 82 / 93

82 Meridian 3

3.16 Perfect Tune

A. PerfectTune must be done after warming 30 minutes at least.

B. PerfectTune must be performed after Auto Color.

C. PerfectTune must be conducted through DVI or scaler embedded patterns.

D. Delta E < 2.5

3.17 Audio

3.17.1 Frequency Response

The amplifier and speaker combination shall provide a frequency response of 300Hz to 20 KHz, with +/-3dB

variation over the entire response range.

3.17.2 Total Harmonic Distortion

Total harmonic distortion shall be limited to 5% THD at the maximum wattage speaker rating specified in

section 1.3, at 1 KHz, when the input is 1.3Vrms.

3.17.3 Power Handling

Each speaker transducer shall accept up to the specified wattage of audio power without damage or

exceeding the frequency response and total harmonic distortion specifications.

3.17.4 Audio Amplifier

The amplifier shall provide two channels of audio up to 1.5Watts per channel from 100Hz to 20 KHz, base

upon an audio signal input of 1.3V RMS per channel.

3.17.5 Volume Control

For monitors with a manual volume control, the direction (at the bottom) of the bezel volume control is “-“key

for minimum volume and “+” key for maximum volume. The default shipping position of the volume control

shall be approximately 90%.

3.17.6 Speaker Sensitivity

The speakers shall support a minimum sensitivity of 75 dB +/-3 dB at 2W /Im at 1 KHz.

3.17.7 Maximum Audio Card Output

The monitor audio amplifier shall accept a maximum input voltage of 1.5 Vrms and meet the following

requirements at the maximum monitor volume setting:

1. The ratings of the audio amplifier may not be exceeded.

2. The ratings of the speakers may not be exceeded.

3. There must not be any clipping of the audio amplifier output signal.

4. Voltage dividers may be used to reduce the input signal level.

3.17.8 Monitor Audio Amplifier Input Impedance

The monitor audio amplifier shall have minimum 10K ohm AC input impedance.

3.18 USB HUB 2.0 Support

Connect the HUB port of the monitor to host PC’s USB port via USB cable, then attach external device to the

downstream port of the monitor. Check if the device can work properly.

Содержание 221P3LPEB/00






























































































Результаты поиска

Содержание 221P3LPEB/00

Отзывы:

Похожие инструкции для 221P3LPEB/00

Бренды по названию

Популярные бренды

Philips 221P3LPEB/00, Руководство по обслуживанию

Результаты поиска

Содержание 221P3LPEB/00

Отзывы:

Похожие инструкции для 221P3LPEB/00

Бренды по названию

Популярные бренды