Philips 14PV360, Инструкция по эксплуатации

Страница: 21 / 23

EN
18
Parental control (Child lock)
This function protects your TV-Video Combi from
unwanted use. All button functions on the front of
the machine are blocked.
1.
1.
Press .
The main menu will appear.
2.
2.
Use to select 'GENERAL SET
UP'. Then press .
3.
3.
Use to select 'CHILD LOCK'.
4.
4.
Use to select 'ON'.
B 1
L C K B
B 1
L C K B
MENU
Programmed recordings will still be recorded (in
spite of the parental control) and cannot be
interrupted.
'If a button at the front of the machine is pressed
while parental control is active, ’CHILD LOCK
ACTIVE’ will appear on the screen for a few sec-
onds.
9. Before you call an engineer
Your TV-Video Combi does not respond to any
button being pressed:
*There is no power supply: check the power supply.
*Parental control is on:Switch the parental control off.
*There is a technical problem: disconnect from the
mains power supply for 5 minutes, then power-up
again.
If this doesn't help, you can reset your
TV-Video
Combi to default factory settings.
Resetting devices to default factory settings
* Warning: by doing so you will the information
stored (TV channels, time and date, TIMER)
will be cleared.
1.Switch the TV-Video Combi to stand-by.
2.Press and hold
and at the
same time for 2 seconds or more.
Cassette is jammed in the TV-Video Combi
*Don’t use force. Disconnect the set from the
mains and reconnect it again after a few sec-
onds.
Remote control does not work
*Remote control is not pointed at the TV-Video
Combi.
*Take out the batteries, wait for 10 seconds and
place them back in the remote control.
*Batteries have run out. Change the batteries.
No picture when you play a cassette
*There is no recording on the cassette.
Poor picture quality when you play a cas-
sette
*The cassette is badly worn-out or of poor quali-
ty. Use a new cassette.
*Tracking is not properly adjusted. Turn to sec-
tion ‘Manual Tracking’.
*Warning, if the tape quality is too bad, the
message ‘Use cleaning tape’ will permanently
appear on the TV screen. If, nevertheless, you
want to see the tape content, press
or
.
P-
P+
P- RECORD
No recording possible
*The TV channel you want to record is not
stored or you selected the wrong programme
number: check TV channels stored.
*A cassette was inserted that does not have the
security tab (cannot be used to record): Insert
a cassette with an intact security tab or change
cassette. For more information, please see the
section ‘Preventing accidental erasing of cas-
settes’ in chapter ‘Manual Recording’.
*’VPS/PDC’ switched on but ‘VPS/PDC time’
wrong: enter ‘VPS/PDC time’ exactly to the
minute. Check your aerial connection.
The wrong TV channel has been recorded
after you programmed a recording using
PlusCode number
1.Enter the PlusCode number you wanted to
record.
2.Confirm with .
3.Check the programme number/channel name
in the ‘PROG.’ input field.
4.If this does not correspond to the desired TV
channel, select the input field and change the
programme number/channel name.
5.Confirm with .
Smart Clock does not work
*You have stored on programme number ‘P01’ a
TV channel that does not transmit TELETEXT.
Store on ‘P01’ a TV channel that transmits
TELETEXT.
*Poor TELETEXT reception. Store a TV channel
on ‘P01’ with good TELETEXT reception.
*You have not activated the Smart Clock func-
tion. Switch the function ‘ON’.
You can also call the customer service centre
in your country.The telephone numbers can be
found on the back of this instruction manual.
Have the model number (MODEL NO) and the
production number (PROD.NO.) of your
TV-
Video Combi
ready.
B 1
B 1
I
f, contrary to expectation, you have any problems
using this TV-Video Combi, it may be caused by the
following reasons.
PAL I(EN).qx3 02.4.2 6:42 PM Page 18