Diagnosis of faults
The washing machine is able to automatically judge some faults by sending out buzzing sound to alarm and indicate the cause
of faults with several indicator light flittering.
Notices:
If the machine is not drain when startup drainage because of air pressure, please lay down the drain hose then put it in the
normal position.
"A
washing machine stops the spinning automatically. After it is changed into water
injection, the pulsator will frequently mix the washing clockwise and couterclockwise (which equals to rinse). That the
weight of the washing is too much or too little, or that the washing machine is not placed evenly will cause the unbalance
in time of spinning and is likely to switch into the automatic rectification and increase the times of rinse. If there is still
abnormal circumstances after checking the above-mentioned points, please pull out the power plug and contact with the
local customer service department . Don't repair it by yourself.
utomatic rectification" is that the
17
18
TROUBLE SHOOTING
Open the cover lid, eliminate the trouble and
close the cover lid.
Power off the washer until
water come to use
Open the cover lid and open
the water tap and close the cover lid
Open the cover lid and clean up
the net then close the cover lid
Power off washer, take off the plug and
make the machine be repaired
C l o s e t h e c o v e r l i d
C l o s e t h e c o v e r l i d
Open the cover lid and distribute
the clothes even, and then close the lid
If no water in water tap
If the water tap not open
If the net of water inlet valve
is stopped up
If the washer is leakaged
If the clothes uneven heavily
If plug is not plugged tight, or the
power switch is not switched on.
Plug the power plug tight and switch
on the power switch.
If no electricity in the socket or the fuse is
broken
Send for electrician to check and repair the
socket or the fuse (see the circuit diagram)
If the power is cut off
If open the cover lid before spinning
If open the cover lid after preset start
If the drain hose is blocked or the mouth of
drain is too high
Symptom
Cause
Solution
Using agin after the power on
Does not
work completely
(Affusion
trouble)
(Door open
warning)
(Scuff the shell
in time of spin)
(Drain trouble)
The following cases are not faults
1.There is the phenomenon of incoming water in time of wash or rinse, which is due to that the water level switch checks the
water level and it supplies water automatically due to the water level drop.
2.There is the phenomenon of intermittent spinning in the beginning of spinning, which is performed to achieve better spinning
effects.
3. In time of rinse with water injection, there may be no drain in the drain hose, which is caused by that the water level does not
reach the overflow mouth due to low water pressure or the low water level set.
4. In the course of spinning, there is a phenomenon of rinsing, which is caused by that the automatic rectification of the
lopsideness of the clothes due to unbalance produced in the course of spinning.
After end of the program
Maintenance of shell
The washing machine will send off the sound of
"DOU-DOU" after end of any program operation
to remind you to take out the washings or operate
it again.
Please shut off the tap, pull out the plug in time of
not in use to avoid water leakage.
Use soft cloth to wipe off the water and dirt on the
surface each time after use of the washing machine.
Detergent, propellant and other chemicals are not
allowed to use to avoid the damages on the surface.
Cleaning of the lint filter
Cleaning of the water inlet
After using the washing
machine for a period, please
clean according the following
steps:
1. Take out the lint filter.
2. Turn the mesh bag outside
and wash it clean in the water.
3. Restore it and refix it.
After long time use, the water inlet mesh bag may be
blocked with crud, and please clean it according to the
following steps:
1. Shut off the tap and switch on the power.
2. Start the washing machine and continue for 5 seconds
(let the water flow in the water inlet hose run into the tub).
3. Load off the water inlet hose, take out the water inlet
mesh bag from the water inlet valve, clean the mesh bag,
then assemble the mesh bag in the valve and load the
water inlet hose.
METHOD OF MAINTENANCE
Method Of Maintenance
