PhD Solutions MXC-UHD-P8X8-HDTL, Руководство по эксплуатации

Страница: 12 / 28

7
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
RDV1
.3 01
/
10
/15 Preliminary release
SAFETY PRECAUTIONS
Please read all instructions before attempting to unpack, install or
operate this equipment and before connecting the power supply.
Please keep the following in mind as you unpack and install this
equipment:
•
Always follow basic safety precautions to reduce the risk of fire,
electrical shock and injury to persons.
• To prevent fire or shock hazard, do not expose the unit to rain,
moisture or install this product near water.
• Never spill liquid of any kind on or into this product.
• Never push an object of any kind into this product through any
openings or empty slots in the unit, as you may damage parts
inside the unit.
• Do not attach the power supply cabling to building surfaces.
• Use only the supplied power supply unit (PSU). Do not use the PSU
if it is damaged.
• Do not allow anything to rest on the power cabling or allow any
weight to be placed upon it or any person walk on it.
• To protect the unit from overheating, do not block any vents or
openings in the unit housing that provide ventilation and allow for
sufficient space for air to circulate around the unit.
REVISION HISTORY
VERSION NO. DATE (DD/MM/YY) SUMMARY OF CHANGE
RDV1
.3 01
/
10
/15 Preliminary release
7
6.6 RS-232 Protocol
MATRIX
►
◄
REMOTE CONTROLLER
Pin Assignment Pin Assignment
1 NC 1 NC
2 TX 2 RX
3 RX 3 TX
4 NC 4 NC
5 GND 5 GND
6 NC 6 NC
7 NC 7 NC
8 NC 8 NC
9 NC 9 NC
Baud Rate: 115200bps
Data bit: 8 bits
Parity: None
Flow Control: None
Stop Bit: 1
6.7 RS-232 and Telnet Commands
COMMAND DESCRIPTION PARAMETER
AN Switch output A to input N. N=1~8
BN Switch output B to input N. N=1~8
CN Switch output C to input N. N=1~8
DN Switch output D to input N. N=1~8
EN Switch output E to input N. N=1~8
FN Switch output F to input N. N=1~8
GN Switch output G to input N. N=1~8
HN Switch output H to input N. N=1~8
IN Switch all outputs to input N. N=1~8
AB…..N Switch output AB... to input N. N=1~8
8
COMMAND DESCRIPTION PARAMETER
SETIP <x.x.x.x><x.
x.x.x><x.x.x.x>
Set IP, SubNet and Gateway
(Static IP)
X=0~255
IPCONFIG Display the current IP
configuration
NONE
RSTIP Set IP configuration to DHCP None
P0 Power off None
P1 Power on None
STOREN Store current I/O to position N N=1~8
SHOWN Show current port N I/O
position
N=1~8
PRESETN Preset the store I/O position N N=1~8
NameN N1 Name port N as N1 N=1~8, N1=A~H (Max
Length=8)
ST Show unit firmware version None
EMN Setting EDID mode N N=1 (Standard)/2 (TV)
RS Routing reset to default None
USBISP Update firmware via USB None
UARTSW? Display the UART switching
state
None
UARTSWN Switch output's UART to port N N=0 (out console), 1~8
UARTBAUD? Display all output’s UART baud None
UARTBAUDN N1 Setting RS-232 routing port N
to Baud rate N1
N=1~8, N1=1~6
(1=9600bps,
2=14400bps,
3=19200bps,
4=38400bps,
5=57600bps,
6=115200bps)
HELP(?) Display all available
commands
None
@FADEFAULT Set to factory default None
QUIT Quit Telnet None
Note: Any commands will not be executed unless followed by a
carriage return. Commands are case-insensitive.