background image

 

2

 

   INTRODUCTION

 

 

 Read the operating instructions carefully before using the product and follow the instructions for safe 

operation. 
 

 PHC Corporation takes no responsibility for safety if the product is not used as intended or is used with 

any procedures other than those given in the operating instructions. 
 

 Keep the operating instructions in a suitable place so that they can be referred to as necessary. 

 

 The operating instructions are subject to change without notice for improvement of performance or 

function. 
 

 Contact our sales representative or agent if any page of the operating instructions is lost or the page 

order is incorrect, or if the instructions are unclear or inaccurate. 
 

 No part of the operating instructions may be reproduced in any form without the express written 

permission of PHC Corporation. 
 

IMPORTANT NOTICE

 

PHC Corporation guarantees this product under certain warranty conditions.    However, please note that 
PHC Corporation shall not be responsible for any loss or damage to the contents of the product. 
 
 
 
<Intended Use> 
This equipment is designed for low temperature storage of biomedical samples. 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание MDF-U54V Series













































Отзывы: