background image

User Manual

PFX1500S

Dear Customer,

Thank you for purchasing the Perform FX PFX1500S.  With decades of experience in design and production,

Perform FX are one of the leading manufacturers of professional effects and lighting equipment.  This fog

machine has been designed and manufactured to the highest of standards, so you can be assured you have

made a good investment. 

For your safety and to ensure you make full use of all the features available, please make sure you read this

manual in full.

Important Safety Advice:

• You must read this manual in full before commencing operation. 

• The machine should be operated by a responsible and competent adult only. 

• Keep this manual in a safe place for future reference.

• Heed all warnings and instructions, both in this manual and on the product.

• Carry and transport this product with care. 

• Impact to this machine or dropping may result in serious mechanical failure.  The machine should not be

used if it has been subjected to such incident.

• Turn off and unplug this machine from the mains supply when not in use.

• This machine is not water-proof and should not be used outside. 

• In the event of any liquid entering the housing, unplug immediately & contact a qualified engineer. 

• You must not attempt to modify this unit

• The manufacturer accepts no responsibility for injury or damage caused as a result of not following the 

manual provided. 

Protection from Electric Shock:

• Only connect this unit to a mains socket with suitable trip and RCD protection.

• To disconnect from the mains socket, always remove by the mains plug. Do not attempt to remove by 

pulling the mains cable.

• Disconnect the unit from the mains supply before cleaning. Cleaning should be carried out with a soft, dry 

cloth.

• Do not submerge or expose this machine to any liquid.

• Do not operate near exposed water or in high humidity.

• Choose a suitable route for mains cables, ensuring trip hazards are avoided and the mains cable is not at 

risk of being crushed.

• Do not open this unit to service. There are no user-serviceable parts inside. Any servicing or repairs should 

be carried out by a qualified engineer only. Any attempt to service or adapt this unit will leave your 

warranty void and could result in serious malfunction or injury.

Protection from Fire:

• Do not place near sources of heat or ignition.

• Do not cover or block any ventilation holes.

• Check your AC wall socket will take the power you are applying to avoid overloading the mains supply.

Содержание PFX1500S









Отзывы: