PFT 00 05 69 13 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 56

PFT 00 05 69 13 Скачать руководство пользователя страница 6

PFT G 54 E

Operating Instructions

09/2006

Knauf PFT GmbH & Co.KG

6

Basic safety instructions

The following terms and symbols are used in these operating instructions for particularly
important information:

NOTE:

Special information for running the machine efficiently

WARNING!

Special information, regulations and restrictions concerning the prevention of damage

WARNING!

The machine should only be used as intended in a perfect technical condition and in compliance with
safety regulations and the operating instructions. It is especially important to immediately eliminate
any faults that could impair safety.

WARNING!

The operating, safety and maintenance regulations must be observed if
integral parts are installed for special types of processing which are not
specified in the current operating instructions.

WARNING!

It is forbidden to use the machine other than intended.

WARNING!

It is forbidden to use the machine within explosive environments.

WARNING!

The machine must always be used in a perfect condition in accordance
with these instructions, while observing the safety instructions and danger
warnings. Any damage which can impair the operational reliability must be
repaired immediately.

WARNING!

The user must be aware of the risk of getting one’s clothes or long hair
caught in movable parts.
Chains, bracelets and rings can also pose a risk.

«
...
4
5
6
7
8
...
»

Содержание 00 05 69 13

























































Отзывы:

Нет отзывов