Pfaff ambition essential 1.0 Скачать руководство пользователя страница 49

Страница: 49 / 59

104 73 15-26

Dismantling and mounting

Main Circuit board - Circuit diagram Ambition 1.0 and1.5

FOR SAFTEY REASONS ALWAYS DISCONNECT THE POWER CORD FROM THE MACHINE BEFORE
REMOVING THE CIRCUIT BOARD AND MAKE SURE TO USE WRIST BAND AND ESD MAT.

ATTENTION!

It is of the utmost importance that precautions are being taken in order to avoid damage of the electronics
by electro static discharges (ESD). To avoid these errors it is important to handle circuit boards in a
controlled way.

Dismantling

1. Remove rear covers.

2. Remove front cover.

3. Disconnect the cables from the circuit board according to below:

4. Remove the 3 screws (A) holding the circuit board.

5. Lift away the PC-board from the machine, and ALWAYS hold the PC board by the edges.

6. Place the PC-board in a ESD Bag.

N1. Transformer

N3. LED lamp

N4. DC motor

N5. Step motor complete (zigzag)

N6. Step motor complete (feed)

N7. Flat cable

N8. Photo sensor complete (needle fl ow,

Needle bar up/down, speed)

N9. Photo sensor board (zigzag)

N10. Photo sensor board (B/H)

N11. Photo sensor board (feed)

N12. Foot controller receptacle

N13. Micro switch (presser foot)

N14. Micro switch (bobbin winder)

N15. IR. Thread detect launcher

N16. Ace. Thread detect receiver Interface bus

N17. Photo sensor complete (thread break)

N18. Micro switch (B/H)

Содержание ambition essential 1.0



























































Результаты поиска

Содержание ambition essential 1.0

Отзывы:

Pfaff ambition essential 1.0, Руководство по обслуживанию, Страница: 49 / 59

Результаты поиска

Содержание ambition essential 1.0

Отзывы: