Pfaff 2438 plusline Скачать руководство пользователя страница 33

Страница: 33 / 118

Sewing

10 - 1

Sewing

In the sewing mode all relevant settings for the sewing operation are displayed. Functions can

be switched on or off by pressing a key. Values for the most important parameters can be

changed directly.

In this mode a difference is made between

manual sewing

and

programmed sewing.

change from manual to programmed sewing, press the PM key. In programmed sewing the

text "PM" appears on the display. The program numbers 1 – 15 can each be used for one

seam program with up to 15 seam sections.

.01

Manual sewing

After the machine has been switched on

(Chapter 7.01 Main switch)

and the manual sewing

mode has been selected with the

key, the display appears for entering the stitch length,

also see

Chapter 9.07 Entering the stitch length.

If the backtack function is switched on, the display appears for entering the backtack values,

also see

Chapter 9.08 Entering the start and end backtacks.

It is possible to switch from one display to the other by pressing the

scroll

key.

2.0

Further functions in manual sewing, also see

Chapter 7.06.02 Function keys:

Start backtacks on/off

Presser foot raised at end of seam on/off

End backtacks on/off

Thread trimming on/off

Needle position raised on/off

Reverse sewing on/off

Presser foot raised on/off

Sensor on/off

Sewing is carried out with the pedal functions, see

Chapter 7.03 Pedal.

Содержание 2438 plusline























































































































Результаты поиска

Содержание 2438 plusline

Отзывы:

Pfaff 2438 plusline, Инструкция по эксплуатации, Страница: 33 / 118

Результаты поиска

Содержание 2438 plusline

Отзывы: