manualshive.com logo in svg

PEUGEOT 205 Cabriolet, Руководство пользователя

ПЕЖО 205 Кабриолет - классический и стильный автомобиль, который обязательно привлечет внимание на дороге. У вас есть возможность скачать бесплатное руководство по эксплуатации для этой модели на {вебсайте}. Не упустите шанс иметь доступ к инструкции в любое удобное время.

Поделиться
Скачать
background image

MOT test checks

REF•11

REF

M

Examine the handbrake mechanism,

checking for frayed or broken cables,
excessive corrosion, or wear or insecurity of
the linkage. Check that the mechanism works
on each relevant wheel, and releases fully,
without binding.

M

It is not possible to test brake efficiency

without special equipment, but a road test can
be carried out later to check that the vehicle
pulls up in a straight line.

Fuel and exhaust systems

M

Inspect the fuel tank (including the filler

cap), fuel pipes, hoses and unions. All
components must be secure and free from
leaks.

M

Examine the exhaust system over its entire

length, checking for any damaged, broken or
missing mountings, security of the retaining
clamps and rust or corrosion.

Wheels and tyres 

M

Examine the sidewalls and tread area of

each tyre in turn. Check for cuts, tears, lumps,
bulges, separation of the tread, and exposure
of the ply or cord due to wear or damage.
Check that the tyre bead is correctly seated
on the wheel rim, that the valve is sound and

properly seated, and that the wheel is not
distorted or damaged. 

M

Check that the tyres are of the correct size

for the vehicle, that they are of the same size
and type on each axle, and that the pressures
are correct.

M

Check the tyre tread depth. The legal

minimum at the time of writing is 1.6 mm over
at least three-quarters of the tread width.
Abnormal tread wear may indicate incorrect
front wheel alignment.

Body corrosion

M

Check the condition of the entire vehicle

structure for signs of corrosion in load-bearing
areas. (These include chassis box sections,
side sills, cross-members, pillars, and all
suspension, steering, braking system and
seat belt mountings and anchorages.) Any
corrosion which has seriously reduced the
thickness of a load-bearing area is likely to
cause the vehicle to fail. In this case
professional repairs are likely to be needed.

M

Damage or corrosion which causes sharp

or otherwise dangerous edges to be exposed
will also cause the vehicle to fail.

Petrol models

M

Have the engine at normal operating

temperature, and make sure that it is in good
tune (ignition system in good order, air filter
element clean, etc).

M

Before any measurements are carried out,

raise the engine speed to around 2500 rpm,
and hold it at this speed for 20 seconds. Allow

the engine speed to return to idle, and watch
for smoke emissions from the exhaust
tailpipe. If the idle speed is obviously much
too high, or if dense blue or clearly-visible
black smoke comes from the tailpipe for more
than 5 seconds, the vehicle will fail. As a rule
of thumb, blue smoke signifies oil being burnt
(engine wear) while black smoke signifies
unburnt fuel (dirty air cleaner element, or other
carburettor or fuel system fault).

M

An exhaust gas analyser capable of

measuring carbon monoxide (CO) and
hydrocarbons (HC) is now needed. If such an
instrument cannot be hired or borrowed, a
local garage may agree to perform the check
for a small fee.

CO emissions (mixture)

M

At the time of writing, the maximum CO

level at idle is 3.5% for vehicles first used after
August 1986 and 4.5% for older vehicles.
From January 1996 a much tighter limit
(around 0.5%) applies to catalyst-equipped
vehicles first used from August 1992. If the
CO level cannot be reduced far enough to
pass the test (and the fuel and ignition
systems are otherwise in good condition) then
the carburettor is badly worn, or there is some
problem in the fuel injection system or
catalytic converter (as applicable).

HC emissions

M

With the CO emissions within limits, HC

emissions must be no more than 1200 ppm
(parts per million). If the vehicle fails this test
at idle, it can be re-tested at around 2000 rpm;
if the HC level is then 1200 ppm or less, this
counts as a pass.

M

Excessive HC emissions can be caused by

oil being burnt, but they are more likely to be
due to unburnt fuel. 

Diesel models

M

The only emission test applicable to Diesel

engines is the measuring of exhaust smoke
density. The test involves accelerating the
engine several times to its maximum
unloaded speed. 

Note: It is of the utmost importance that the
engine timing belt is in good condition before
the test is carried out. 

M

Excessive smoke can be caused by a dirty

air cleaner element. Otherwise, professional
advice may be needed to find the cause.

4

Checks carried out on

YOUR VEHICLE’S EXHAUST
EMISSION SYSTEM

Содержание 205 Cabriolet










































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 205 Cabriolet

Fabbri BICI OK 2 Quick Start Manual preview
BICI OK 2
Бренд: Fabbri Страницы: 4
GOgroove SMARTmini AUX Operating Manual preview
SMARTmini AUX
Бренд: GOgroove Страницы: 9
Kuda-Phonebase 055040 Installation Instruction preview
055040
Бренд: Kuda-Phonebase Страницы: 3
Honda 08A28-0J6-800 Installation Instructions Manual preview
08A28-0J6-800
Бренд: Honda Страницы: 32
Yakima K674 Instructions Manual preview
K674
Бренд: Yakima Страницы: 13
Menabo 000081000000, Fitting Instructions Manual preview
000081000000,
Бренд: Menabo Страницы: 11
AA Products SR-A260 Instruction Manual preview
SR-A260
Бренд: AA Products Страницы: 4
Cadillac 1997 Catera Owner Assistance Information preview
1997 Catera
Бренд: Cadillac Страницы: 34
Oldsmobile 2000 Oldsmobile Intrigue Owner'S Manual preview
2000 Oldsmobile Intrigue
Бренд: Oldsmobile Страницы: 348
Volvo S90 2018 Quick Manual preview
S90 2018
Бренд: Volvo Страницы: 42
Ecco 13 Series Installation And Operation Instructions Manual preview
13 Series
Бренд: Ecco Страницы: 24
Tabernus Peram Hatch-bag Luggage System Installation Instructions Manual preview
Hatch-bag Luggage System
Бренд: Tabernus Peram Страницы: 10
Jaeger 21010508J Fitting Instructions Manual preview
21010508J
Бренд: Jaeger Страницы: 14
Ranger design 1525-PC Installation Manual preview
1525-PC
Бренд: Ranger design Страницы: 22
Audiovox Prestige 128-8602 Installation Manual preview
Prestige 128-8602
Бренд: Audiovox Страницы: 8
Blue Ox BX1120 Installation Instructions preview
BX1120
Бренд: Blue Ox Страницы: 5
Charge Amps Halo Pole Mount Manual preview
Halo Pole Mount
Бренд: Charge Amps Страницы: 14
Istar PI00670 Instruction Manual preview
PI00670
Бренд: Istar Страницы: 6

Бренды по названию

Популярные бренды

Загрузить еще бренды