background image

 

2.4.

 

Li-Po protection 

 

Li-Po protection – enter programming mode for any selector position, 

pull the trigger 10 

times

, and hold the trigger until a sound signal can be heard to save the settings. 

 
Batteries  should  never  be  discharged  below  certain  level.  Perun  V3  offers  a  feature  which 
warns its user that his Li-Po battery is almost completely discharged and should be changed. 
 
With  Li-Po  protection  enabled,  Perun  will  automatically  detect  number  of  Li-Po  cells  in 
connected battery and if voltage for that number of will drop below safe limits, short sound 
signals will be heard every 30 seconds. 
 

2.5.

 

Double shot 

 

Double shot – enter programming mode for any selector position, 

pull the trigger 11 times

and hold the trigger until a sound signal can be heard to save the settings. 

 
When  double  shot  feature  is  enabled,  if  single  fire  mode  is  used,  shots  will  be  fired  both 
after the trigger has been pulled and relased. 

 

2.6.

 

Calibration mode 

 

Calibration mode - enter programming mode for any selector position, 

pull the trigger 12 

times

, and hold the trigger until a sound signal can be heard to save the settings. 

 
Enabling  this  function  will  make  Perun  V3  enter  calibration  mode  at  next  start-up.  This 
feature  is  meant  mainly  for  technicians  and  more  information  about  it  can  be  found  in 
installation manual. 

 

 

Содержание V3 Optical









Отзывы: