background image

Form No. Z2280

7

Perlick is committed to continuous improvement. Therefore, we reserve the right to change specifications without prior notice.

Cleaning the Beer System – 

Direct Draw Dispensers Self-Contained

The entire beer system, to include the faucet, flexible
beer line and tapping devices must be cleaned at 
regular intervals. We recommend flushing the entire
system with fresh water immediately after a keg has
been emptied. Once each month the system should
be cleaned chemically.

It is recommended that you purchase Perlick’s
Pump Type Cleaning Kit. It is equipped with an
adapter that attaches directly to the faucet shank,
jar with pump, cleaning solution, faucet brush and
spanner wrench.

Cleaning the draft beer system will help to 

eliminate the buildup of the following materials:

■   

Bacteria:

Beer is an excellent food for bacteria (none of 
which is harmful). Proper conditions may begin 
the growth of bacteria in draft beer and on the 
beer faucet. By regular cleaning, we prevent 
this bacterial buildup and maintain the quality 
of the draft beer. Greenish or yellowish colored 
material on the faucet may indicate bacterial 
growth.

Yeast:
All domestic draft beers contain a small amount 
of yeast which remains in the beer from the 
fermentation process. When the temperature of 
draft beer exceeds 50° a process of secondary 
fermentation may take place. The beer faucet 
may exhibit a white colored substance (yeast 
build up) if not cleaned on a regular basis.

Beer Stone:
All beer contains calcium which is present from 
the grains used in the brewing process. it is an 
important natural material in draft systems in 
that as it oxidizes it coats the internal parts of 
the beer lines and equipment. This thin coat of 
beer stone helps prevent the beer from picking 
up strong metallic or plastic flavors as it flows 
through the system. The beer stone will 
continue to build if the system is not cleaned 
properly or regularly and can cause drawing 
problems if it begins to flake off. Beer stone is 
present if one can see a brownish color on the 
faucet or inner wall of the beer line, or tobacco-
like flakes in the beer.

Cleaning the Cabinet

Use a mild detergent and water to clean the inside
and outside of the cabinet. Dry thoroughly. Never
use a scouring pad or abrasive cleanser. 
NOTE: An industrial strength, commercial cleaner
can be used to clean the outside of painted 
cabinets. 

Cleaning the Condenser

Use a long handled, stiff brush to clean the dirt from
the front surface of the condenser. Keeping the
condenser free from dust and dirt will ensure effi-
cient operation. 
CAUTION: Do not bend the fins while brushing the
front of the condenser. 

Содержание DP32













Отзывы: