Perle SR-100 Series Скачать руководство пользователя страница 16

Perle SR-100 Fast Ethernet Media Converter Installation Guide                             16

 

Technical Specifications 

The following applies to all SR-100 media converters. 

Input Supply Voltage 

9.6-60VDC 0.4A max, unregulated 
(12/24/48-VDC nominal) 

Power Consumption 

2.4 watts

 

Operating Temperature 

-10°C - 60°C (14°F - 140°F 

Storage Temperature: 

-40°C - 85°C (-40°F - 85°F) 

Operating Temperature (XT) 

-40°C - 75°C (-40°F -167°F)

 

Storage Temperature (XT) 

-40°C - 85°C (-40°F -185°F) 

Operating Humidity: 

5% to 90% non-condensing 

Storage Humidity: 

5% to 95% non-condensing 

Operating Altitude: 

Up to 3,048 m (10,000 ft.) 

Weight: 

0.12kg 

Dimensions SC 

114 x 100 x 22.5 mm 

                    ST 

126 x 100 x 22.5 mm 

                    SFP 

117 x 100 x 22.5 mm 

Safety 

UL/ULC/EN 62368-1 

CAN/CSA C22.2 No. 62368-1-14 

UL 61010-1 and UL 61010-2-201 

Laser Class I Safety – IEC 60825-1:2014 

IEC-60825-1:2014 standard and complies with FDA/CDRH  

21 CFR1040.10 and 21 CFR1040.11

 

EMI/EMC 

FCC 47 Part 15 Class A 

ICES-003 

EN55032(CISPR32) 

EN61000-6-4 

EN55024 

IEC/EN 61000-6-2 General Immunity for Industrial Environments 

IEC/EN 61000-4-2 (ESD): Contact: 

EN 61000-4-3 (RS) 

EN 61000-4-4 (EFT) 

EN 61000-4-5 (Surge 

EN 61000-4-6 (CS) 

EN 61000-4-8 (PFMF) 

EN 61000-4-11 

Содержание SR-100 Series























Отзывы: