Perle IDS-509FPP Скачать руководство пользователя

Страница: 24 / 35

IDS-509FPP Hardware Installation Guide

Interfaces

RJ45 Ports

RJ45 PoE/PoE+ Ports

PoE Output

•

1 - shielded RJ45 (509F2PP)

•

Up to 100 meters (328 ft.)

•

Auto-negotiation

•

Auto-MDI/MDIX

•

Ethernet isolation 1500 V

Voltage

: voltage will match input voltage.

Power Output:

PoE devices 15.4 Watts
PoE+ devices 30 Watts

Amount of available power to PoE/PoE+ ports is
dependent upon sufficient voltage and power being
supplied to the switch.

Note:

Power output can be managed through software

configuration.

100Base-X Fiber Ports

•

2 -3 100Base-X in a variety of wavelengths,
distances and connectors

Console port

•

RJ45 DTE - serial port

•

MicroUSB Type B female port - serial interface

Switch properties

Standards

IEEE 802.3 for 10Base-T

IEEE 802.3u for 100Base-TX

IEEE 802.3ab for 1000Base-T

IEEE 802.3x for Flow Control

IEEE 802.3af or IEEE 802.3at type 1

Environmental Specifications

Operating Temperature Ranges

IDS-509FPP

IDS-509FPP-XT

-10° C to 60° C (14° F to 140° F).

-40° C to 75° C (-40° F to 167° F)

Storage Temperature Range

IDS-509FPP

IDS-509FPP-XT

-25° C to 70° C (-13° F to 158° F)

-40° C to 85° C (-40° F to 185° F)

Operating Humidity Range

5% to 90% non-condensing

Storage Humidity Range

5% to 90% non-condensing

Operating Altitude

Up to 3,048 meters (10,000 feet)

Technical Specifications

Содержание IDS-509FPP




































Результаты поиска

Содержание IDS-509FPP

Отзывы:

Похожие инструкции для IDS-509FPP

Бренды по названию

Популярные бренды

Perle IDS-509FPP, Руководство по установке оборудования

Результаты поиска

Содержание IDS-509FPP

Отзывы:

Похожие инструкции для IDS-509FPP

Бренды по названию

Популярные бренды