Perkins 4.236 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 54

Perkins 4.236 Series Скачать руководство пользователя страница 44

4

38

User’s Handbook, TPD 1291E, Issue 2

4.236 Series

How to clean the engine breather valve

Note:

A breather valve is fitted only to 4.2482 engines.

1

Disconnect the hose clips and remove the pipe between the induction manifold and the breather valve (A).

2

Release the clamp screw and remove the breather valve from the rocker cover.

3

Seal the small hole (A1) in the top cover of the breather valve with a water proof tape.

4

Wash the breather valve in kerosene and dry it with low pressure air. Remove the seal from the top of the

breather valve.

5

Ensure that the pipe fitted between the breather valve and the induction manifold is clean.

6

Fit the breather valve to the rocker cover. Fit the pipe between the induction manifold and the breather valve.

7

Tighten the clamp screw of the breather valve and then the hose clips.

This document has been printed from SPI². Not for Resale

«
...
42
43
44
45
46
...
»

Содержание 4.236 Series























































Отзывы:

Нет отзывов