Perkins 4.236 Series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 54

Perkins 4.236 Series Скачать руководство пользователя страница 24

3

18

User’s Handbook, TPD 1291E, Issue 2

4.236 Series

How to start a cold engine with KBi or electrically operated start pilot

If necessary, renew the screw type canister. Ensure that the sealing washer remains in position when the new
canister is fitted. Each container has a safety valve.

If the engine is equipped with a manual stop control, ensure that it is in the "run" position.

Adjust the engine speed control to the maximum speed position.

Turn the start key to the "S" position (A) in order to engage the starter motor.

When the engine turns, press the starting aid button for a maximum period of 2 seconds. If the engine does
not start after the first 2 second application, keep the starter motor engaged. After 5 seconds, press the button
again for 2 seconds.

Allow the start switch to return to the "R" position, when the engine starts. Then adjust the engine speed control
to get an even idle speed. In certain conditions it is necessary to inject a little more fluid after the engine has
started, in order to ensure that the engine continues to run.

KBi equipment must not be used with heater type cold starting aids such as the fuelled starting aid.

This document has been printed from SPI². Not for Resale

«
...
22
23
24
25
26
...
»

Содержание 4.236 Series























































Отзывы:

Нет отзывов